How to Calculate Total Force on a Charge at the Center of Curvature?

  • Thread starter Thread starter mateoguapo327
  • Start date Start date
  • Tags Tags
    Electromagnetism
AI Thread Summary
To calculate the total force on a charge at the center of curvature of a semicircular line of charge, one must consider the electric field produced by the charge distribution. The charge per unit length is given by the expression [lamb] = [lamb]naught cos [theta], and the total charge on the semicircle is 12.0 microcoulombs. By integrating the vertical component of the electric field from the semicircle, the resulting force on a charge of 3.00 microcoulombs is determined to be approximately -0.70588 N, aligning closely with the book's answer of -0.707 N. The calculations involve determining [lambda]0 and integrating the electric field contributions from each infinitesimal segment of the semicircle. Properly showing work in future problems is encouraged for clarity.
mateoguapo327
help! I need help with this homework problem.

--A line of positive charge is formed into a semicircle of radius R=60.0 cm. The charge per unit length along the semicircle is described by the expression [lamb]= [lamb]naught cos [the] . The total charge on the semicircle is 12.0 microcoulombs. Calculate the total force on a charge 3.00 microcoulombs at the center of curvature.--

The figure shows the semicircle with is center at the origin going from 0 to pi. [the] is the angle formed by dragging R clockwise from the positive y axis.

the answer in the book is -0.707Nj and I got -0.526N. Can someone please help me figure out how to properly go about solving this problem?
 
Physics news on Phys.org


consider the electric field at the center of the semicircle due to a little piece of the semicircle at angle θ. by symmetry, only the vertical component of this field contributes:

dEy = - 1/4πε0 cos θ dq/r2 = - 1/4πε0 cos θ λrdθ/r2 = - 1/4πε0 cos2 θλ0dθ/r

then integrate from π/2 to -&pi/2:

Ey = -λ0/4πε0r∫cos2 θ dθ = -λ0/8ε0r


the force on the charge is the Fy = qEy


we also need to solve for λ0.

Q = ∫dq = ∫λ0rcos θ dθ = 2rλ0

λ0 = Q/2r

finally
Fy = -qQ/16ε0r2


plug in the numbers and you get -0.70588 N.
 
Ahem!

Mateoguapo:

https://www.physicsforums.com/showthread.php?s=&threadid=28

In the future, please show your work first.

Thanks,
 
oops. my bad.
 
Thread 'Variable mass system : water sprayed into a moving container'
Starting with the mass considerations #m(t)# is mass of water #M_{c}# mass of container and #M(t)# mass of total system $$M(t) = M_{C} + m(t)$$ $$\Rightarrow \frac{dM(t)}{dt} = \frac{dm(t)}{dt}$$ $$P_i = Mv + u \, dm$$ $$P_f = (M + dm)(v + dv)$$ $$\Delta P = M \, dv + (v - u) \, dm$$ $$F = \frac{dP}{dt} = M \frac{dv}{dt} + (v - u) \frac{dm}{dt}$$ $$F = u \frac{dm}{dt} = \rho A u^2$$ from conservation of momentum , the cannon recoils with the same force which it applies. $$\quad \frac{dm}{dt}...
I was thinking using 2 purple mattress samples, and taping them together, I do want other ideas though, the main guidelines are; Must have a volume LESS than 1600 cubic centimeters, and CAN'T exceed 25 cm in ANY direction. Must be LESS than 1 kg. NO parachutes. NO glue or Tape can touch the egg. MUST be able to take egg out in less than 1 minute. Grade A large eggs will be used.
Back
Top