Magnetic Force on a Current Carrying Wire

AI Thread Summary
The discussion centers on determining the direction of the magnetic field acting on a current-carrying wire. Initially, it was assumed that the magnetic field (B) was in the +y direction, but the correct answer is -y. The right-hand rule is emphasized, where the thumb points in the direction of the magnetic force, and the fingers in the direction of the current. For maximum force, the current must be perpendicular to the magnetic field, leading to the conclusion that the field must curl downwards in the -y direction. This clarification helps resolve the confusion regarding the orientation of the magnetic field.
taliaroma
Messages
5
Reaction score
0
The figure shows a current i through a wire in a uniform magnetic field , as well as the magnetic force acting on the wire. The field is oriented so that the force is maximum. In what direction is the field?

I have uploaded the figure, and the relevant equations.

My reasoning:
-L is in the direction of i.
-Assume i is a positive value.
Therefore, B is in the direction of +y.

However, the key says the answer is -y.

Why is that?
 

Attachments

  • physics.gif
    physics.gif
    2.4 KB · Views: 863
Physics news on Phys.org
You're doing the right hand rule incorrectly. Your thumb needs to be pointing in the direction of the magnetic force. When you do this and orient your fingers to point in the direction of i in the picture, you will see that they curl down, in the -y direction.
 
taliaroma said:
The figure shows a current i through a wire in a uniform magnetic field , as well as the magnetic force acting on the wire. The field is oriented so that the force is maximum. In what direction is the field?

I have uploaded the figure, and the relevant equations.

My reasoning:
-L is in the direction of i.
-Assume i is a positive value.
Therefore, B is in the direction of +y.

However, the key says the answer is -y.

Why is that?

Homework Statement

Homework Equations


The Attempt at a Solution


Think about it this way:

What has to be the orientation of L and B in order for the force to be the maximum? What does theta have to be? I am assuming you understand that it is perpendicular since you narrowed it down to the y direction. Now you have two choices, either the + y direction or the - y direction. Assuming you have a positive charge and the force is out of the page in z direction (thumb points out of the page, fingers point in direction of current towards left, -x direction, now which way do your fingers naturally naturally curl?). This is the direction of the magnetic field (assuming its not changing and is uniform). Does that make sense?
 
sona1177 said:
Think about it this way:

What has to be the orientation of L and B in order for the force to be the maximum? What does theta have to be? I am assuming you understand that it is perpendicular since you narrowed it down to the y direction. Now you have two choices, either the + y direction or the - y direction. Assuming you have a positive charge and the force is out of the page in z direction (thumb points out of the page, fingers point in direction of current towards left, -x direction, now which way do your fingers naturally naturally curl?). This is the direction of the magnetic field (assuming its not changing and is uniform). Does that make sense?

Yes, that's very helpful. Thank you!
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top