Maximizing Range: Tips for a High School Physics Project

  • Thread starter Thread starter profkth
  • Start date Start date
  • Tags Tags
    Project
AI Thread Summary
To maximize the range of a soda can for a high school physics project, consider using a spring mechanism instead of batteries and rubber bands. The spring should be fixed to a vertical rod and compressed to generate maximum force when released, allowing the can to travel further. Adding traction with rubber bands around the can can help prevent slipping at the start. Using denser materials, like steel washers, may also improve performance by increasing angular momentum. Implementing these strategies can help achieve the goal of moving the can at least 10 feet.
profkth
Help! My son has spent countless hours on his high-school physics project, where the challenge is to make a soda can move as far as possible on its own. Nothing can be placed between the can and the floor surface, and nothing can extend beyond the ends of the can by more than 7 mm. Beyond that, anything goes. He is able to get it to move, using rubber bands and batteries taped to the rubber bands, inside the can, but it only moves about 5 feet. He will only get a passing grade on the project if he makes it move at least 10 feet. Any ideas?
 
Physics news on Phys.org
Hi

Have u tried the Sling Shot technique? or have u tried filling the can completely with pressurised soda/gas and then opening the cork so that the can moves forward? or u could even use a spring


Sridhar
 
Thanks! What is the sling shot technique?
 
I'm assuming that the batteries are inside the can, wound up with rubber bands. When they are released, they spin, and the can starts turning, and rolls some distance.

Is the can slipping when it starts?
If so, put a few fat rubberbands around it so it will get better traction.

Can you get something denser than a battery? A big stack of steel or copper washers might impart more angular momentum.

Njorl
 
Hi

Ok, the sling shot technique is one where u use a fully stretched rubber band. However I have been calculating a few things. You would get a better range if u used a spring technique. Here are the procedures:

1) Fix one end of the spring to a vertical rod that stands on the ground.

2)Fix the other end of the spring to the Can and compress the spring to the maximum possible extent. i.e The spring should be completely compressed.

3) Now the tie the can to the stick using strings

4) To release the can, just cut the strings.

4 a) If u don't want to use the strings, u culd hold the can using urself and release it when u want.

5) I don't think this apparatus will have more that 7mm extension on each side.

6) Use a spring with a very high spring constant.i.e. A highly compressible spring that can generate lots of force.

You will definitely get an excellent range as the Force generated by the spring = -K*x, where x = the length to which the spring is compressed and k = spring constant. This provides a momentum to the Can and:

kx = mv, where, m = mass of the can and v = velocity of the can.

Therefore, v = (k*x)/m; Which means that more the spring is compressed, the faster the can goes and thus greater the distance it covers. Don't use a very heavy can or a very light can. Use a Coke Tin with some paper in it .


Hope this helps you.

Sridhar
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...

Similar threads

Back
Top