Pin Diagram of 8:1 Mux - Get Answers Here!

  • Thread starter Thread starter And 1
  • Start date Start date
  • Tags Tags
    Diagram Pin
AI Thread Summary
A request for a labeled pin diagram of an 8:1 multiplexer (Mux) initiated the discussion, highlighting difficulties in finding this information. A link to a relevant Texas Instruments datasheet was shared for reference. Participants clarified that pin #5 is the True output (Y), pin #6 is the Inverted output (W), and pin #7 serves as the strobe/chip enable/gate input (G), which is active low. Additionally, pin #8 is designated as GND (ground). This exchange successfully provided the needed clarifications regarding the pin functions of the 8:1 Mux.
And 1
Messages
12
Reaction score
0
Could anyone please provide me with a labeled pin diagram of an 8:1 Mux or list it on here? I have tried searching and haven't had much luck. Thanks for your help.
 
Engineering news on Phys.org
Wonderful! Thank you!
 
Pin locations #5, #6, and #7 are labeled as Y, W, and G. Would some please clairfy these?

Please note that pint #8 is GND (ground). Thanks again for your help.
 
Y is the True output.
W is the Inverted output (complement of Y).
G is a strobe/chip enable/gate input which is active low.
 
Thank you!
 

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

Charlieplexing: LEDs have different brightness
Replies
14
Views
2K
How can I reroute multiple signals from a 4 pin connector using a relay switch?
Replies
37
Views
6K
Unconventional wire illustration/diagram.
Replies
6
Views
1K
Understanding operation of specific SMPS example (is it a flyback?)
Replies
2
Views
2K
Is My Thyristor Gate Driver Circuit Malfunctioning Due to Component Issues?
Replies
12
Views
2K
Why Does My PIC16F723A Show a Programming Error in MPLAB X?
Replies
2
Views
3K
Connecting a 5 pin nte7077 voltage regulator
Replies
3
Views
3K
Identifying Pin Joints & Rollers - Structural Analysis Homework Help
Replies
20
Views
4K
OrCad Capture CIS -- Unconnected pin, no FLOAT property or FLOAT = e
Replies
2
Views
7K
B Help w/ repairing/refurbishing an equatorial mount
Replies
11
Views
2K

Hot Threads

Recent Insights

Back
Top