Refractive Index: Part A, B, & C

AI Thread Summary
Part A of the refractive index homework was confirmed to be correct, while Part B was completed successfully using Snell's Law. For Part C, the key point is that the ray is totally internally reflected at the critical angle, which is indicated to be 27 degrees. The discussion emphasized that no complex formulas are needed for Part C, as it is worth only one mark. Clarification was provided that the critical angle should be measured from the normal, not the angle of incidence.
zain1612
Messages
2
Reaction score
0
Part A i just need to know if i have done it properly.
Part B is done
Part c don't have a clue :cry:

Homework Statement



2ryg5.jpg


Homework Equations


Law of refraction n1*sinχ1=n2*sinχ2
Critical Angle sine(x) = nr/ni

The Attempt at a Solution



part a is on the image above

part b I have done it

Part c no idea
 
Physics news on Phys.org
Read the wording of the question very carefully...the ray is totally internally reflected at P for the first time...
This means that the ray is striking the surface at the critical angle... can you see which angle is the critical angle??
 
Part A All OK.
Part B apply snells law you have all the info!

Part C I have looked at the question paper on the the AQA website and part c is worth 1mark! This means no formula are needed!
The important line is "At this point the angle of relfection is 27 and the ray is totally internally reflected for the first time."
 
bm0p700f said:
Part A All OK.
Part B apply snells law you have all the info!

Part C I have looked at the question paper on the the AQA website and part c is worth 1mark! This means no formula are needed!
The important line is "At this point the angle of reflection is 27 and the ray is totally internally reflected for the first time."

And technician directly addressed that issue.

Another way to look at this is that the critical angle is angle of incidence for which the angle of refraction would be 90° .

I hope that helps.
 
Thanks guys I just reliased I was being stupid. I was taking the angle of incident for the critical angle to be 27° instead of taking it from the normal. Thanks for the help:-p
 
I was writing this as technician was writing. He pressed submit before I did that's all!
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top