Solving for Velocity of Particle in 2D Plane

AI Thread Summary
Two forces act on a 1.70 kg particle initially at rest, with known forces F1 and F2. The calculated velocity components at 9.4 seconds are (38.7i - 49.7647j) m/s, and the direction is 307.87 degrees. The discussion emphasizes using standard constant acceleration equations rather than relying on final velocity for calculations. The importance of incorporating the initial position in the calculations is also highlighted. Correct application of these principles leads to accurate results in determining the particle's motion.
PeterFer
Messages
6
Reaction score
0

Homework Statement



Two forces, vector F 1 = (3 i - 2 j) N and vector F 2 = (4 i - 7 j) N, act on a particle of mass 1.70 kg that is initially at rest at coordinates (-1.70 m, +4.25 m).

i know that the components of the velocity at 9.4 seconds are (38.7i - 49.7647j)m/s
i also know that the direction the particle is moving at 9.4 seconds is 307.87 degrees

Homework Equations





The Attempt at a Solution


some how everything I do brings me to (363.78i - 467.788j)m which is wrong
 
Physics news on Phys.org
Welcome to PF!

Hi PeterFer! Welcome to PF! :smile:

You don't need, and shouldn't use, the final velocity …

(it's misled you into using s = vt)

just use one of the standard constant acceleration equations

(and don't forget to add on the initial position). :wink:
 


ah yea thank you, i ended up realizing that myself but thank you anyway
 

Thread 'Errors and significant figures'

I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
View full post »
Thread 'Minimum mass of a block'

Thread 'Minimum mass of a block'

Here we know that if block B is going to move up or just be at the verge of moving up ##Mg \sin \theta ## will act downwards and maximum static friction will act downwards ## \mu Mg \cos \theta ## Now what im confused by is how will we know " how quickly" block B reaches its maximum static friction value without any numbers, the suggested solution says that when block A is at its maximum extension, then block B will start to move up but with a certain set of values couldn't block A reach...
View full post »
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'

Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'

Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is（Figure 2）： F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
View full post »

Similar threads

Find the value of ##T## and distance of particle in the first ##4## seconds
Replies
2
Views
916
Body attached to a block by a spring, shaped like an inclined plane
Replies
1
Views
914
1D Particle & Energy w/ F(x): Am I doing this right?
Replies
7
Views
1K
Finding velocity and work of a collision
Replies
5
Views
2K
Relative Velocity and Angles of Movement (Sears & Zemansky's Exercise)
Replies
11
Views
2K
A massless disk with an embedded particle rolls down an inclined plane
Replies
17
Views
1K
Charge on a particle above a seemingly infinite charge plane
Replies
2
Views
5K
Potential Energy - 2D inelastic collision - ballistic pendulum
Replies
10
Views
2K
Max Impulse on a pendulum
Replies
1
Views
781
Are the 2nd and 3rd problems in this video correctly solved? (charged dipole and organ pipe problems)
Replies
3
Views
991

Hot Threads

Recent Insights

Back
Top