Special relativity: rectangular box moving 0.5c

AI Thread Summary
A rectangular box at rest in frame S' has dimensions of 2m, 2m, and 4m, with S' moving at 0.5c relative to frame S. The correct gamma factor for this scenario is approximately 1.1547, which affects the length contraction of the box's dimensions. Consequently, the volume in the moving frame S' should be larger than in frame S, contrary to the initial calculations. After correcting the values, the volume in S' is found to be approximately 13.85m^3. The discussion emphasizes the importance of accurately applying the principles of special relativity to determine the effects of motion on volume.
scustin
Messages
4
Reaction score
0

Homework Statement



A rectangular box at rest in S' has sides a'=2m, b'=2m, c'=4m. The side c' is parallel to z' axis of S'; the side b' forms an angle 45deg with x' axis of S'. S' moves with v=0.5c with respec to S, along its x axis. Find the volume of the box in S and S'.

Homework Equations



gamma= 1/sqrt(1-v^2/c^2)
gamma= Lp / L
V=l*w*d

The Attempt at a Solution


gamma = 1.33333
L(a') = 1.06066
V(S') = 12m^3
V(S) = 16m^3
am I right about S' ??
 
Physics news on Phys.org
No, you made a couple of mistakes. First, your value for gamma isn't correct. Second, length contraction should affect both a' and b' since neither side is parallel to the y' axis.

You should have also realized your answer was wrong because the volume of the box is largest in its rest frame. In a frame where it's moving, it'll be length-contracted, so its volume will decrease. V(S') should be bigger than V(S).
 
I had it backwards, 16m^3 was my S', 12 was what i got for S.
 
Ok i found the mistake, gamma should be 1.1547, making L(a) 1.22456m, and the area 13.85m^3, if i am right
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top