Speed, Acceleration and Time - SUVAT Equations and Speed Time Graph

AI Thread Summary
A car travels at a constant velocity of 50 m/s for 4 seconds before decelerating at 10 m/s² until it stops. The velocity at 8 seconds is calculated to be 10 m/s, while at 12 seconds, the car's speed is 0 m/s due to complete deceleration. The total distance traveled after 12 seconds is determined to be 370 meters, accounting for both the distance covered during constant speed and during deceleration. The discussion emphasizes the importance of understanding the difference between distance traveled and displacement, as well as the correct interpretation of the problem's wording. Accurate graphing of acceleration and speed over time is also highlighted as essential for visualizing the motion.
mm391
Messages
65
Reaction score
0

Homework Statement



In 4 seconds a car travels with constant velocity of 50m/s. After 4 seconds the car decelerates at 10m/s^2 until velocity = 0. What is the velocity at 8 and 12 seconds and what is the distance traveled after 12 seconds?

Also how would I draw the acceleration time graph and relate that to a speed time graph?

Homework Equations



f(t)=U(t)+a(t^2/2)=s


The Attempt at a Solution



But this does not seem to give me the correct answer. I was told the total distance is 370 meters
 
Physics news on Phys.org
8 seconds total is 4 seconds after the deceleration starts. So the velocity at t=8s is equal to 50 m/s - 4 s ( 10 m/s2 ) = 10 m/s

12-4=8 so 50 m/s - 8 s ( 10 m/s2 ) = -30 m/s, however the deceleration end at v= 0 m/s. So the speed actually is 0 m/s.

To find the total distance traveled one has to find to the moment the car first has speed v=0. To do that solve the equation: 50 m/s - tstop ( 10 m/s2 ) = 0
Solving gives tstop = 5 s (actually 5 s for the moment deceleration so 9 seconds total)
The average speed traveled is (50 m/s + 0 m/s)/2 = 25 m/s (this work only if the deceleration or accelaration is constant)
The distance traveled during deceleration is 25 m/s * 5 s = 125 meters
The distance traveled before deceleration is 50 m/s * 4 s = 200 meters
The total distance traveled is 325 meters.

An acceleration vs time chart would look like this (x-axis should be t-axis):
http://www4c.wolframalpha.com/Calculate/MSP/MSP20271a1ifb1cc14f2e4i000043e243867d21fe1a?MSPStoreType=image/gif&s=41&w=290&h=123&cdf=RangeControl

A speed vs time chart would look like this (x-axis should be t-axis):
http://www4c.wolframalpha.com/Calculate/MSP/MSP731a1ifd56g88acbe20000156h79ga9hi13fed?MSPStoreType=image/gif&s=37&w=290&h=136&cdf=RangeControl

A location vs time chart would look like this:
http://www4c.wolframalpha.com/Calculate/MSP/MSP6251a1ifd95dbc17f8b00006842i3gc0ig97h33?MSPStoreType=image/gif&s=26&w=287&h=127&cdf=RangeControl
 
Last edited by a moderator:
Zaal post is not correct.
The question is the distance traveled not displacement.
Try to draw the diagram.
Start with constant velocity of 50m/s
At t=4secs, draw line with gradient -10 till t=12sec.
Add the areas(both sides taken as positive, since it is distance covered) and you get the answer.
 
azizlwl said:
Zaal post is not correct.
The question is the distance traveled not displacement.
Try to draw the diagram.
Start with constant velocity of 50m/s
At t=4secs, draw line with gradient -10 till t=12sec.
Add the areas(both sides taken as positive, since it is distance covered) and you get the answer.

Sorry I made one mistake I corrected it (I forgot to add the distance traveled before deceleration).
PS Don't forget v=0 for t>9
 
Your graph should be extended till t=12sec
The distance =4(50)+(50)(50)/20 +1/2(10)(3)2 =200+125+45=370m
 
azizlwl said:
Your graph should be extended till t=12sec
The distance =4(50)+(50)(50)/20 +1/2(10)(3)2 =200+125+45=370m

You ignore the following sentence of the problem:

After 4 seconds the car decelerates at 10m/s^2 until velocity = 0.

The wording of the problem is confusing.

ehild
 
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Back
Top