Understanding Power Supply Ratings and Compatibility

AI Thread Summary
A 9VAC 1.3A power source is needed for a digital guitar effects pedal, but finding one can be challenging. The discussion emphasizes that both voltage and current ratings are crucial for compatibility; using a 12VAC 1A source with a resistor to drop voltage is not advisable. The difference between AC and DC is significant, as AC cannot be directly substituted for DC without damaging the device. A transformer is necessary to convert the higher wall socket voltage (120VAC or 240VAC) down to the required 9VAC. Understanding these specifications is essential for ensuring proper device operation and longevity.
sdusheyko
Messages
18
Reaction score
0
Hello

i need a 9VAC 1.3A source but it's hard to come by... is there a way i can use a similar source?

i don't know too much about this sort of thing but from what i understand the power output is more important than the individual current or voltage out... is that right? for example, my source would have to be around 12W output (p=iv=1.3*9=11.7watt.) or does the current and voltage rating actually matter?

could i add a resistor to say a 12vac 1a source to drop the voltage to get what i need?

what about vac verses vdc; does this really matter? if my wall socket output is 3p anyway, isn't that like vdc since it's constant?

i'm confused, any help would be much appreciated!
 
Engineering news on Phys.org
sdusheyko said:
Hello

i need a 9VAC 1.3A source but it's hard to come by... is there a way i can use a similar source?

i don't know too much about this sort of thing but from what i understand the power output is more important than the individual current or voltage out... is that right? for example, my source would have to be around 12W output (p=iv=1.3*9=11.7watt.) or does the current and voltage rating actually matter?

could i add a resistor to say a 12vac 1a source to drop the voltage to get what i need?

what about vac verses vdc; does this really matter? if my wall socket output is 3p anyway, isn't that like vdc since it's constant?

i'm confused, any help would be much appreciated!

The answers to your questions mostly depend on what the AC power source is feeding. What device are you powering, and what are its input power requirements/specifications?
 
9VAC 1.3A digital guitar effects pedal.
 
sdusheyko said:
Hello

what about vac verses vdc; does this really matter? if my wall socket output is 3p anyway, isn't that like vdc since it's constant?
i'm confused, any help would be much appreciated!

your 3 pin wall socket socket will be supplying 120VAC or maybe 240VAC depending on which country you live in.
And yes that's very different to DC and it matters greatly. Put any sort of AC voltage into a unit that requires a DC voltage and it will probably have an extremely short life span

If for example you are in the USA with 120VAC and you need 9VAC then you need to buy a transformer to drop from 120V to 9V

Dave
 
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Back
Top