What is the final speed of the ball when the goalie catches it?

  • Thread starter Thread starter ian_durrant
  • Start date Start date
  • Tags Tags
    Kinematics
AI Thread Summary
The discussion focuses on calculating the final speed of a soccer ball when caught by a goalie after being kicked at an initial speed of 19.2 m/s at a 65.8° angle. The initial velocities in the x and y directions were determined to be 7.87 m/s and 17.5 m/s, respectively. It was clarified that gravitational acceleration only affects the y-direction, and the x-direction speed remains constant. To find the final speed when the ball reaches the net, the time of flight must be calculated, followed by determining the final velocities in both directions. The final speed can then be computed using the Pythagorean theorem, combining the x and y velocities.
ian_durrant
Messages
20
Reaction score
0
[SOLVED] Kinematics in 2-dimesions

Homework Statement



A soccer player kicks the ball toward a goal that is 25.0 m in front of him. The ball leaves his foot at a speed of 19.2 m/s and an angle of 65.8 ° above the ground. Find the speed of the ball when the goalie catches it in front of the net. (Note: The answer is not 19.2 m/s.)

Homework Equations



x=V(0)t+(1/2)gt^2

V^2=V(0)^2+2gy

V= sqrt(Vx^2+Vy^2)

The Attempt at a Solution



Ok let me define all the variables I've got so far

V(0)= 19.2

Vx0= 7.87
x= 25 (12.5 for one half)
gx= 0? (not so sure about this one)
Vx= ?(at top of apex )

Vy= 0 (at top of apex)
gy=-9.8
y= 15.626
Vy0= 17.5 (initial y veolicty)

Ok so the first thing I did was find the inital velocity for the x and y componets using sine and cosine, so

V0x= 19.2cos65.8= 7.87
V0y=19.2sin65.8= 17.5

I then used my inital y velocity to find out the heigth (y distance) of the shot

Vy^2= Vy0^2+2gy
0= (17.5)^2+2(-9.8)y
y= 15.625

I'm unsure where to go now in order to out the speed of the ball when the goalie catches it i know that V= sqrt (Vx^2+Vy^2). Should i try and figure out the two final velocities and then plug them into that equation?
 
Last edited:
Physics news on Phys.org
You need to find the time at which the ball reaches the position of the net. What you've written as g_x is actually just acceleration in the x-direction, g is simply used to denote gravitational acceleration (which only occurs in what's defined as the y-direction in this problem). If air resistance is ignored, acceleration in the x-direction is 0.

Thus you know speed in the x-direction will not change over the course of the motion. Once you've found the time, you need to find the x and y velocities, and as you said, the square root of the sum of their squares is the speed at that point.
 
Ahhh i see it now, the height wasn't even needed in this problem, thanks for the tip.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top