Why does this rectifier have a large AC output voltage?

AI Thread Summary
The discussion revolves around unexpected AC voltage readings from a bridge rectifier designed for a simple LED circuit. Users noted that there is still an AC voltage present at points expected to output DC, with measurements showing nearly double the transformer voltage. The readings were taken using a multimeter, which can yield peak voltage readings that may confuse users. Suggestions were made to incorporate a capacitor to stabilize the power supply and reduce noise. The conversation emphasizes the importance of understanding multimeter settings and proper measurement techniques in rectifier circuits.
motioncity
Messages
4
Reaction score
0
I made a (bridge) rectifier for a simple circuit that would make several LEDs light up. When it was finished, I used a multimeter to measure the voltages between several points and got the readings you can see in http://users.pandora.be/k-a-d/rectifier.jpg". Why is there still an AC voltage between the two points that were supposed to be DC-only? And why is it almost twice the original transformer voltage? The resistor code is pretty blurry in the image; it's 2.2k if it helps.
 

Attachments

  • rectifier.jpg
    rectifier.jpg
    22.5 KB · Views: 484
Last edited by a moderator:
Engineering news on Phys.org
How are you getting that 20V AC number? I'm guessing it's with a multi-meter of some sort. A cheap way to make AC voltage measurements is to use half a bridge rectifier, measure peak voltage, and multiply by 2.

You could test this by measuring the AC voltage of a battery using the same tool.

P.S. You might want to stick a capacitor in there to clean up the power supply. Otherwise it will be noisy.
 
Last edited:
Indeed, the reading comes from a multimeter. I simply switched between "V DC" and "V AC".
 
Take a look at http://www.allaboutcircuits.com/vol_3/chpt_3/4.html" to see where you're getting the AC.

Regards
 
Last edited by a moderator:

Thread 'Underwater piezoelectric sensor array receive sensitivity'

Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
View full post »

Thread 'Following up on the recent thread about Earth Resistance measurements'

I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
View full post »

Thread 'Question about bonding ground and neutral'

I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
View full post »

Similar threads

Resistive heating power AC vs rectified AC/DC
Replies
10
Views
4K
Need to use a rectifier.... but where to put it?
Replies
7
Views
2K
AC to DC voltage doubler not working
Replies
7
Views
4K
Creating a stable 5V DC supply out of 6 V (RMS) AC
2
Replies
63
Views
7K
Understanding Dual Output Zener PSU
Replies
7
Views
4K
Is it possible to charge/discharge this cap fast enough?
Replies
9
Views
2K
Help designing a bridge rectifier
Replies
7
Views
2K
Bridge Rectifiers: How Do They Work?
Replies
6
Views
3K
Voltage Output in subtractor photocircuit
Replies
1
Views
1K
AC generator output voltage to grid question
Replies
4
Views
2K

Hot Threads

Recent Insights

Back
Top