Year 12 Sound Problem (Involves resonance in a closed pipe).

AI Thread Summary
The discussion revolves around a physics problem involving resonance in a closed pipe, where the pipe resonates at frequencies of 288 Hz and 512 Hz with a distance of 13.9 cm between resonance points. The user seeks clarification on how to approach the problem, particularly regarding the relationship between frequency, wavelength, and the length of the pipe. They initially attempted to calculate the wavelength and expressed confusion about whether to use the entire pipe length or just the distance between resonance points. After some calculations, they arrived at a velocity of sound in the tube as 232.9 m/s, but later realized a mistake in their equations. The conversation emphasizes understanding the fundamental principles of resonance in closed pipes to solve similar problems effectively.
caitie_72
Messages
4
Reaction score
0

Homework Statement



Hi :)
This question is from a test i had today. For some stupid reason we get to finish it off tomorrow. I figured i do what everyone else will, and sort out the what i didn't understand. Luckily this was it. Anyway, the question is typed from memory so it may seem a bit odd or inaccurate.

A pipe is in a tub of water. As it is moved down (or up, can't remember!) it resonates at 288 Hz and 512 Hz. The distance between these two points is 13.9 cm (0.139 m). What is the velocity of sound in the tube?

I'm not sure of the order of frequencies occurring is. I think it was probably the lowest frequency first. I don't really need an answer, just an understanding of how to do a problem like this. All i know is that the pipe resonates at those two frequencies, and the distance between the points where it resonates is 13.9m. If you've ever seen a question like this ... then you'd probably get what i mean, hopefully.
Do I used simultaneous questions? I'm not sure.

Homework Equations


(w=wavelength)
v=F*w

The Attempt at a Solution


What i did first, in a fit of irrational confusion, was find the wavelength. I assumed that resonance was occurring at either nodes or antinodes, half a wavelength apart (?)
So w = 2 * 13.9.

Then i got confused, because i know the fundamental wavelength of a closed pipe is w=4L.

Then i did something stupid i knew wasn't right. Found the difference between the frequencies and then multiplied it with the wavelength. Stupid stupid, i know. Makes no sense.

I'm thinking simultaneous equations?
f=v/4L.

512=3v/4L 288=v/4L

Resonance must be occurring at first and second modes, right?
I'm just confused about what the length is! Does length, in this case, mean the length of the whole pipe or the length between the points of resonance? Does resonance occur at half wavelengths or quarter wavelengths? Don't understand!

Any help or direction at ALL is appreciated. Thanks :)
 
Physics news on Phys.org
Since there is no other information, you have to assume that they are resonating in the fundamental mode.
So write 512=3v/4L 288=v/4L as 512=v/4L1,and 288=v/4L2. Write these equation in terms of L1 and L2. L1 - L2 is given. Solve for v.
 
Thank you so much! You are seriously my favourite person ever right now.
Just checking, am i doing it right?

L1=3v/2048
L2=v/1152

0.139 = 3v/2048 - v/1152
v = 232.9 m/s

I assume so. Thanks again :)
 
L1=3v/2048
This is wrong. It should be L1=v/2048. Find L2-L1.
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Struggling to make relation between elastic force and height'
Hello guys this is what I tried so far. I used the UTS to calculate the force it needs when the rope tears. My idea was to make a relationship/ function that would give me the force depending on height. Yeah i couldnt find a way to solve it. I also thought about how I could use hooks law (how it was given to me in my script) with the thought of instead of having two part of a rope id have one singular rope from the middle to the top where I could find the difference in height. But the...
Back
Top