A real life problem, just for fun

  • Thread starter Thread starter catkin
  • Start date Start date
  • Tags Tags
    Fun Life
AI Thread Summary
The discussion revolves around an observed phenomenon in an "ant channel" where surface water movement indicated a potential leak, but it transitioned to a still surface abruptly. The interface between the moving and still water was noted to move at half the speed of the surface water. Participants are encouraged to explore explanations for this behavior, with hints suggesting a possible change in water depth. The inquiry remains open for further insights and guesses about the underlying physics. The conversation highlights the complexities of fluid dynamics in a controlled environment.
catkin
Messages
215
Reaction score
0

Homework Statement



Around one of our buildings we have an "ant channel" of roughly square cross section (say 20 cm x 20 cm) with fish in it to control the mosquito larvae. The surface of the water carries particles giving a good indication of any surface movement.

Late one afternoon we observed the surface moving relatively quickly (say 3 cm/s). Suspecting a leak we followed the moving surface water and were amazed to find that the moving surface gave way abruptly to a still surface. Watching a little longer we observed that the interface between moving and still areas of the surface was itself moving -- at about half the velocity of the moving surface.

It appeared as if there was a discontinuity in the flow of water.

Homework Equations



None.

The Attempt at a Solution



I think I can explain the phenomenon. If no one gets it, I'll give clues.
 
Physics news on Phys.org
Hm. I'm not sure. But can I hazard a guess? There's a change in the depth of the water?
 

Thread 'Rolling without slipping on a curved surface'

Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
View full post »
Thread 'Correct statement about a reservoir with an outlet pipe'

Thread 'Correct statement about a reservoir with an outlet pipe'

The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
View full post »
Thread 'A bead-mass oscillatory system problem'

Thread 'A bead-mass oscillatory system problem'

I can't figure out how to find the velocity of the particle at 37 degrees. Basically the bead moves with velocity towards right let's call it v1. The particle moves with some velocity v2. In frame of the bead, the particle is performing circular motion. So v of particle wrt bead would be perpendicular to the string. But how would I find the velocity of particle in ground frame? I tried using vectors to figure it out and the angle is coming out to be extremely long. One equation is by work...
View full post »

Similar threads

Real life problem - pushing object up incline plane
Replies
6
Views
7K
Problem Set Involving Inertia and Balloons
Replies
2
Views
2K
Problem set with air conditioners and thermodynamics
Replies
5
Views
2K
Sink time of a cap with varying hole diameters
Replies
21
Views
9K
Work on Block with an opposing force
Replies
3
Views
9K
I Can the "measurement problem" just be an "epistemological ambiguity"?
Replies
15
Views
2K
Optics, interference, very unusual problem
Replies
16
Views
3K
Just curious about many things like hydrostatics
Replies
28
Views
4K
Power Delivered From Black Body
Replies
4
Views
2K
How can power and work be calculated using friction and known mass and distance?
Replies
8
Views
8K

Hot Threads

Recent Insights

Back
Top