Calculating Hydrogen Mass Storage in Compressed Vessels

AI Thread Summary
The discussion focuses on finding an equation to calculate the mass storage of hydrogen in compressed vessels. The original poster references a specific tool for this purpose and seeks to develop a similar internal solution. Participants discuss the compressibility factor (z) and its relevance in calculating mass based on volume, temperature, and pressure. There is also mention of other equations of state, like van der Waals, which could be applicable. The conversation emphasizes the importance of understanding these concepts for accurate calculations in hydrogen storage.
Brool
Messages
2
Reaction score
0
Hello all;

I am looking for an equation for calculating mass storage of Hydrogen in compressed vessels
I have fount the following link (https://nanosun.co.uk/hydrogen-tools) which provides what i need but would like to create something similar for internal use

Can you suggest an approach to this?

Regards;
Haim
 
Physics news on Phys.org
Are you familiar with the concept of compressibility factor z?
 
Chestermiller said:
Are you familiar with the concept of compressibility factor z?
hi Chester,

to some level.
 
Brool said:
hi Chester,

to some level.
Then you know how to calculate the mass, given the volume, temperature, and pressure? Also, are you familiar with other equations of state, like van der Waals?
 

Thread 'Average velocity as a weighted mean'

Hello everyone, Consider the problem in which a car is told to travel at 30 km/h for L kilometers and then at 60 km/h for another L kilometers. Next, you are asked to determine the average speed. My question is: although we know that the average speed in this case is the harmonic mean of the two speeds, is it also possible to state that the average speed over this 2L-kilometer stretch can be obtained as a weighted average of the two speeds? Best regards, DaTario
View full post »

Thread '1:1 versus 2:1 Mechanical Advantage debate'

The rope is tied into the person (the load of 200 pounds) and the rope goes up from the person to a fixed pulley and back down to his hands. He hauls the rope to suspend himself in the air. What is the mechanical advantage of the system? The person will indeed only have to lift half of his body weight (roughly 100 pounds) because he now lessened the load by that same amount. This APPEARS to be a 2:1 because he can hold himself with half the force, but my question is: is that mechanical...
View full post »
Thread 'Beam on an inclined plane'

Thread 'Beam on an inclined plane'

Hello! I have a question regarding a beam on an inclined plane. I was considering a beam resting on two supports attached to an inclined plane. I was almost sure that the lower support must be more loaded. My imagination about this problem is shown in the picture below. Here is how I wrote the condition of equilibrium forces: $$ \begin{cases} F_{g\parallel}=F_{t1}+F_{t2}, \\ F_{g\perp}=F_{r1}+F_{r2} \end{cases}. $$ On the other hand...
View full post »

Similar threads

A Temperature and pressure change in an air vessel
Replies
3
Views
2K
B The physics of flywheel launchers (like tennis ball shooters)
2
Replies
60
Views
4K
Hydrogen-fueled Internal Combustion Engine (ICE)
Replies
18
Views
5K
I Hydrogen plasma compression with liquid Mercury piston
Replies
1
Views
2K
How to calculate time of Pressurization in vessel?
Replies
15
Views
4K
I Work-Energy Theorem for Moving Block and Spring System?
Replies
4
Views
2K
Calculating Pressure & Mass for Hydrogen Tank Filling
Replies
7
Views
4K
Calculation of Pressure in a Cylinder with an orifice on its surface
Replies
3
Views
2K
Calculate Final Speeds Two Mass Spring System
Replies
9
Views
5K
What is the ultimate internal stress of silica aerogels in compression mode?
Replies
2
Views
382

Hot Threads

Recent Insights

Back
Top