Changes in velocity with Direction change

AI Thread Summary
Tim's change in velocity is calculated using the formula Δv = v2 - v1, where v1 is 6.4 m/s south and v2 is 5.8 m/s west. The components of the velocities can be represented as v1 = (0, 6.4) and v2 = (5.8, 0), leading to Δv = (5.8, -6.4). While the change in velocity can be expressed as a vector, the magnitude, which is the hypotenuse of the resulting triangle, may also be of interest. Clarification on whether to include angle or direction in the answer depends on the specific requirements of the question. Proper representation of axes is crucial for unambiguous communication of the velocity components.
skatergirl
Messages
9
Reaction score
0

Homework Statement



Tim is running cross country at 6.4m/s when he completes a wide angle turn and continues at 5.8m/s[w]. What is his change in velocity?


Homework Equations



Δv=v2-v1
a2+b2=c2

The Attempt at a Solution



i am not sure how i am supposed to find the change in velocity...
i could just find the hypotenuse but i think that is giving me the resulting acceleration and not the actual change. but I am quite sure its not as simple as just subtracting the two values either ??
 
Physics news on Phys.org
You have to remember that velocity is a vector: so we have v_1 = (0,6.4) and v_2 = (5.8,0) (where (1,0) points West and (0,1) points South), so as you correctly wrote: \Delta v = v_2 - v_1 = (5.8, -6.4). This is technically the change in his velocity, but the question may be just asking for its magnitude (which, as you note, is the hypotenuse).
 
Last edited:
ok i will include both in my answer then. thank you. also should i be including the angle/direction? do you draw the s or w arrow first when drawing the diagram? like will the angle be between the hyp and 5.8 or the hyp and 6.4?
 
skatergirl said:
also should i be including the angle/direction?

If you include the information about what your axes are (i.e. South = (0,1), West = (1,0) ) then when you write the components of \Delta v down you have represented it unambiguously. You shouldn't need to include it unless the question specifically asks you for it.

do you draw the s or w arrow first when drawing the diagram? like will the angle be between the hyp and 5.8 or the hyp and 6.4?

I'm not sure I understand the first question. In answer to the second, you would have to be specific (e.g. "the vector is 10° to the East of North", or "at a bearing of 010°" or some similar specification of angle - and note that was just an example, not the direction of \Delta v)
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top