Choosing the Right Tolerance for Bearing Housing Design: A Scientist's Guide

AI Thread Summary
When designing a bearing housing for an axle, understanding the appropriate tolerances for the axle to bearing bore and bearing outer diameter is crucial. The choice of fit—clearance, interference, or transition—depends on the application requirements, with clearance fits being recommended for light duties, especially when using Loctite for assembly. Familiarity with tolerance types from resources like SKF is beneficial, but practical application guidance is still needed. The discussion highlights the importance of selecting the right tolerances to ensure proper function and reliability in the bearing housing design. Clear guidance on tolerances will enhance the overall design process.
Wilson123
Messages
58
Reaction score
2
I'm currently in the process of designing a bearing housing for an axle. Unfortunately I am not 100% on the diameter of my axle yet but I want to have a clear understanding what tolerances to use on my axle to bearing bore and bearing outer diameter to the bearing housing.

I've looked over the SKF website to familiarise myself with the different types of tolerances however I'm still unsure on how I should pick the right tolerance for my application and also what fit I want to achieve (clearance, interference or transition).

Any help or guidance on what I should be looking at to define this would be very helpful.
 
Engineering news on Phys.org
Clearance with Loctite is the easiest one to use for light duties and/or where available skills and equipment are limited .
 
Nidum said:
Clearance with Loctite is the easiest one to use for light duties and/or where available skills and equipment are limited .

This sounds suitable for my design.

What about considering tolerances?
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Find 3D Printer & Software Resources for Prototype Creation'

I'd like to create a thread with links to 3-D Printer resources, including printers and software package suggestions. My motivations are selfish, as I have a 3-D printed project that I'm working on, and I'd like to buy a simple printer and use low cost software to make the first prototype. There are some previous threads about 3-D printing like this: https://www.physicsforums.com/threads/are-3d-printers-easy-to-use-yet.917489/ but none that address the overall topic (unless I've missed...
View full post »

Similar threads

Appropriate tolerance for shaft and housing for bearings?
Replies
2
Views
2K
How to Design an Airtight Tubing with a Motor Shaft?
Replies
5
Views
2K
Analyzing the Mechanics of a Wobble Plate in a Cranked Axle Mechanism
Replies
10
Views
3K
What is the best beam design for my aluminum tandem axle trailer?
Replies
33
Views
5K
How do I properly mount a needle bearing for a trike swing arm?
Replies
11
Views
3K
Torque calculations: Rotating vertical shaft
Replies
5
Views
5K
Calculating Axial Thrust for a Wheelchair Axle
Replies
4
Views
2K
What Bearings Suit a Shaft with Varying Loads and Diameters?
Replies
3
Views
2K
Considerations for design of lead screw + guide rail set up
Replies
8
Views
4K
ATV quad, front wheel ball bearings not tappered roller bearings.
Replies
1
Views
3K

Hot Threads

Recent Insights

Back
Top