How Is Converted Electrical Energy Stored and Utilized?

AI Thread Summary
Converted electrical energy can be stored using various methods, including pumped hydro, thermal storage, batteries, and capacitors. Pumped hydro is currently the only proven large-scale storage solution, while thermal systems can store energy for short-term use in heating applications. Batteries are becoming increasingly viable for energy storage, with advancements making them more affordable and efficient, exemplified by products like the Tesla Power Wall. Capacitors are effective for very short-term storage but are not suitable for longer durations. Overall, while there are promising developments in energy storage, pumped hydro remains the dominant method today.
laclry311
Messages
5
Reaction score
0
TL;DR Summary
looking for how energy conversion stores and applies electric current
Hello, I am interested in the circuitry of energy conversion, such as solar, thermal, etc. How does the converted electrical energy get stored, for example, do they use supercapacitors? How does it then get applied for general use? Do you have any documentation or circuit diagrams for this?
 
Engineering news on Phys.org
What research have you done so far? What have you found out?
 
  • Like
Likes berkeman
Welcome to the PF. :smile:

Are you familiar with Maximum Power Point Tracking in power conversion like solar and wind? That's an important piece of the puzzle. For more information on your general questions, I'll page @anorlunda -- he has written several Insights Blogs about the power grid and power conversion.
 
laclry311 said:
Summary: looking for how energy conversion stores and applies electric current

How does the converted electrical energy get stored
There are several ways to store electric energy.
  1. Pumped hydro. Use electric power to pump water to a reservoir on a mountain top. Later let the water run down generating electricity. This is the one and only storage method proven to work on a huge scale. But it can only be used in locations able to hold a large reservoir on a mountain top.
  2. Thermal. Your home hot water heater can use electricity to heat the water late at night for use later in the day when people are up. Ditto for house warming/cooling to store for a couple of hours.
    Geothermal systems can store warm/cold water for heating/cooling purposes underground. Some of them store so much that they can be used seasonally. But the number of installations are very small, so I guess the reason must be cost.
  3. Batteries. Batteries are great, but so far they are too big, too expensive, or too short-lived for many applicaitions. But that is changing rapidly. Utility scale batteries are a tiny fraction of the grid today, but growing rapidly. Devices such as the Tesla Power Wall are very attractive for houses with solar power.
  4. Capacitors store energy very well, for a few milliseconds, but for periods of hours or days, they are very far from being competitive to 1) 2) or 3)
  5. Flywheels have been tried, without much success.
So, there is great interest in electric energy storage. The future looks promising, but the status today is that pumped hydro is the only really large scale energy storage system proven to be economically attractive. Wide spread utility battery storage will come hopefully within 5-10 years.
 
  • Like
Likes berkeman
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top