Helicopter Physics: Finding Time to Reach Ground from Release Point

  • Thread starter Thread starter chocolatelover
  • Start date Start date
  • Tags Tags
    Helicopter Physics
AI Thread Summary
The height of a helicopter releasing a mailbag is described by the equation h=2.55t^3, with the bag released at 1.85 seconds. To find the time it takes for the mailbag to reach the ground, the initial height at the moment of release must be calculated using the given formula. The initial velocity of the mailbag is debated, with some asserting it is zero while others suggest it should be calculated based on the helicopter's height at release. The gravitational acceleration is factored into the equation h=vit+1/2at^2 to solve for the time until the bag hits the ground. Ultimately, the calculations yield a time of approximately 1.56 seconds for the mailbag to reach the ground after release.
chocolatelover
Messages
238
Reaction score
0

Homework Statement


The height of a helicopter above the ground is given by h=2.55t^3, where h is in meters and t is in seconds. At 1.85 s, the helicopter releases a small mailbag. How long after its release does the mailbag reach the ground?


Homework Equations





The Attempt at a Solution



_____________________________h=2.55t^3
1.85s

h=2.55(1.85s)^3

Thank you very much
 
Physics news on Phys.org
I'm fairly sure that you can make use of the formula:

h=v_{i}t+\frac{1}{2}at^2

And do it as you started:

2.55(1.85)^3=v_{i}t+\frac{1}{2}at^2

And then initial velocity is zero, and a is the gravitational constant g=9.8m/s^2:

2.55(1.85)^3=0t+\frac{1}{2}9.8t^2

And then solve for t.
 
methotrexate said:
I'm fairly sure that you can make use of the formula:

h=v_{i}t+\frac{1}{2}at^2

And do it as you started:

2.55(1.85)^3=v_{i}t+\frac{1}{2}at^2

And then initial velocity is zero, and a is the gravitational constant g=9.8m/s^2:

2.55(1.85)^3=0t+\frac{1}{2}9.8t^2

And then solve for t.
WHO IN THE WORLD TOLD YOU THAT THE INITIAL SPEED OF THE BAG IS ZERO?
 
Thank you very much

If it isn't 0, how would you solve it?

Would you do this?

velocity:
h=3.25t^3
h'=9.75t^2
h'(1.65)=9.75(1.62)^2
=26.5444

position:

h=3.25(1.65)^3
=14.6m

I would then use all of this to solve for t, right?

h=vit+1/2at^2
14.6m=26.5444m/s+1/2(-9.8m/s^2)t^2
t=1.56s

Thank you
 
Last edited:
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Back
Top