How Can I Build a Basic Transistor Amplifier for My Phone's Speaker?

AI Thread Summary
To build a basic transistor amplifier for a phone's speaker, it's essential to connect the amplifier's input to a 3.5mm audio jack correctly, linking ground to ground and either left or right audio to the amplifier. Using op-amps is recommended for simplicity, and a power source, like a wall wart, is necessary for operation. While some circuit diagrams suggest using a Darlington transistor, a standard transistor can be used with lower-value resistors, though care must be taken with input connections to avoid improper DC levels. A single transistor design may not work effectively due to the speaker loading down the amplifier. Proper schematics and guidance can be found through various online resources for building a functional amplifier.
ajbwarrrior
Messages
9
Reaction score
0
Hi,
I have a single 2 watt, 8 ohm speaker from an old radio that i wired directly to a headphone audio jack and tried it in my phone. as you can probably guess, my phones speakers are much louder.

How could i make a basic transistor amplifier that could give decent volume from the speaker?

I have seen many circuit diagrams for this but i don't know how a device would be connected to them.

Any schematics that would suit this application would be greatly appreciated.
 
Engineering news on Phys.org
You can do it with opamps, or discrete transistors. I'd recommend opamps. Just look at google images for audio amplifier IC and start reading about an approach. Note that amplifiers require a power source which can be as simple as a wall wart.
For example:
http://www.rason.org/Projects/icamps/icamps.htm
 
  • Like
Likes 1 person
with the amp in the link, how would the input be connected to a 3.5mm auxiliary jack ?
 
The link shows a mono amplifier. The 3.5 jack has three rings, ground, left, and right. You would connect ground to ground and either left or right to the amp (or use a stereo IC with 2 amps). Or, you could make a resistive mixer where you connect both L and R to the input, each through, say, a 1K resistor.
 
  • Like
Likes 1 person
I don't think that will work for what you are doing. It requires the proper DC levels on the input, and drives a continuous DC signal through the speaker when there is no signal. It is a pretty specialized hack for his radio application.

Look at this page --- Question 5 is probably the simplest design that will work, question 8 shows a 1 transistor approach.
http://www.allaboutcircuits.com/worksheets/trouble_bjtamp.html

The problem with the 1 transistor approach is that the speaker loads down the amp.
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...

Similar threads

Replies
37
Views
4K
Replies
20
Views
3K
Replies
29
Views
4K
Replies
41
Views
6K
Replies
9
Views
9K
Back
Top