How Much Force is Needed to Lift a Shed Hatch?

  • Thread starter Thread starter kewsky
  • Start date Start date
  • Tags Tags
    Force Lift
AI Thread Summary
The discussion focuses on the mechanics of lifting a hatch door in a shed, specifically its required lifting force, the force needed to maintain it in an open position, and the forces exerted on the hinge. The hatch will be hinged at the top and open outward, with considerations for counterweights or air struts to assist in lifting. The point of force application is crucial, as it affects the amount of force needed to lift the door from a vertical to a horizontal position. There are suggestions to explore alternative designs, such as conventional side-hinged doors, depending on the intended use of the hatch. Overall, the conversation emphasizes the importance of calculating forces and considering design options for effective functionality.
kewsky
Messages
2
Reaction score
2
I plan to build a hatch door in one side of my shed. The plan is that the hatch door will be hinged at the top long edge. The hatch door will open from the bottom long edge. The hatch door will open out and up to a horizontal position (possibly slightly past horizontal). My question is what lifting force will be required to lift the door, what force will be required to keep the door in the open position, what forces (value and direction) will be exerted on the hinge during lifting and open. Sizes have not been decided yet so assume door size; horizontal length = L, vertical height = H, weight of door =W. Gravity here is normal. Any help, advice or insight would be appreciated.
 
Engineering news on Phys.org
An additional thought. Could a counterweight be added to aid lifting without building outside the shed?
 
  • Like
Likes sophiecentaur
The counterweight can either be on a lever or on a pulley, pulling up the hatch. There are also airstruts (as on car hatchback doors) available.
The formula for the force, if the door starts hanging vertical, will, of course, where the handle is. If the handle is half way up the door, the force will be almost zero at the start and go to the value of the door weight when it's horizontal (if you are pulling it vertically) then it gets less when lifting further.
I think you will need to produce a diagram giving some idea of where and how the force will be applied to the door. Direction and point of application will have a huge effect on the actual force you need
I am not sure what you want do do but you might find https://www.sgs-engineering.com/help-advice/how-to-calculate-the-force-required-for-a-gas-strut/ helpful if you want to make the job easy for a person who's not too strong, even if the door is heavy.
 
kewsky said:
The plan is that the hatch door will be hinged at the top long edge. The hatch door will open from the bottom long edge. The hatch door will open out and up to a horizontal position (possibly slightly past horizontal).
Sorry to be Captain Obvious here, but why not just use a conventional door with side hinges? Is there some need for the hatch door to end up horizontal and high up?

What kinds of things pass through the open hatch? Just people and animals, or small equipment, or car-size vehicles, etc?
 
berkeman said:
What kinds of things pass through the open hatch?
Who let the dogs out?
 
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'
Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
Back
Top