Measure flow rate with a manometer (pressure gauge)

AI Thread Summary
To measure the air flow rate from a leakage in a 50-liter volume pressurized to 1 bar, the initial air volume needed to maintain that pressure must be calculated. When the pressure drops to 0.5 bar, the volume of air that has escaped can be determined by the difference in air volume required for each pressure level. The discussion highlights that the flow rate will vary with the changing pressure difference. Using example figures, if 10 liters are needed for 1 bar and 5 liters for 0.5 bar, the leakage rate could be estimated at 10 liters per minute. Understanding these calculations is crucial for accurately assessing leakage in pressurized systems.
Xefyros
Messages
3
Reaction score
0
Hello!

I have a volume of 50 liters which I pressurize with air so that I read 1 bar on the manometer.
But there is a leakage in the volume so after 30 sec the manometer shows 0,5 bar.

What is then the air flow ( liter / min) of the leakage?
 
Physics news on Phys.org
The flow rate will change as the pressure difference changes.
 
scottdave said:
The flow rate will change as the pressure difference changes.

Hello, maybe bad explained but I would want to know if you can count how much air you have to fill up the 50 liter volume with to get 1 bar (over) pressure and then how much air that has left when the manometer reaches 0,5 bar.
So let's say that you need to fill up the volume with 10 liter for 1 bar and 5 liter for 0,5 bar pressure -> then over 30 seconds it has left 5 liter ( from 1 bar to 0,5 bar) and we would then have ~~10 liter / min
(just example numbers)
 

Thread 'Is calling fictitious forces "not real" just about terminology?'

Hi there, im studying nanoscience at the university in Basel. Today I looked at the topic of intertial and non-inertial reference frames and the existence of fictitious forces. I understand that you call forces real in physics if they appear in interplay. Meaning that a force is real when there is the "actio" partner to the "reactio" partner. If this condition is not satisfied the force is not real. I also understand that if you specifically look at non-inertial reference frames you can...
View full post »

Thread 'Derivation of Hamilton's Principle: Questions'

I have recently been really interested in the derivation of Hamiltons Principle. On my research I found that with the term ##m \cdot \frac{d}{dt} (\frac{dr}{dt} \cdot \delta r) = 0## (1) one may derivate ##\delta \int (T - V) dt = 0## (2). The derivation itself I understood quiet good, but what I don't understand is where the equation (1) came from, because in my research it was just given and not derived from anywhere. Does anybody know where (1) comes from or why from it the...
View full post »

Similar threads

A manometer measures mechanical or thermodynamic pressure?
Replies
1
Views
2K
Measuring the water volume in a small tank with a manometer
Replies
26
Views
2K
I Does gas flow from low to high pressure?
4
Replies
160
Views
9K
Measuring changes in barometric pressure without a barometer
Replies
21
Views
4K
I Flow rate calculation of coating application
Replies
30
Views
2K
PressureDrop/Pressure/Volumetric flow rate calculation (in a Pipe)
Replies
5
Views
4K
Fluid Forces in a Manometer: Understanding Pressure and Kinetic Energy
Replies
2
Views
1K
Chemistry What is "gauge pressure" and how does a manometer work?
Replies
1
Views
2K
Air flow through a hole in a submerged pressure tank
Replies
13
Views
21K
How pressure is measured using a manometer
Replies
2
Views
2K

Hot Threads

Recent Insights

Back
Top