Self Cleaning Rack-and-Pinion Design?

AI Thread Summary
The discussion centers on the challenges of using a rack-and-pinion system in a dirty environment where traditional sealing methods are not viable. Participants suggest using self-lubricating materials like Metalon to reduce dust accumulation and prevent seizing. Another idea proposed is to implement a constant lubrication system, such as spraying oil or water onto the mechanism. Additionally, some users reference successful applications in off-road vehicles that utilize heavy-duty bellows to protect against dirt and debris. Creative solutions, such as using a mechanical scraper, are also mentioned as potential ways to maintain functionality in harsh conditions.
fester225
Messages
8
Reaction score
0
I have an application which would work very nicely with a rack-and-pinion. The problem is: the environment is inherently very dirty, and covering it isn't an option. Using the usual arrangement would cause it to quickly seize.

Does anyone know of a self cleaning rack-and-pinion design?
 
Engineering news on Phys.org
What do you mean self cleaning rack & pinion ?
I can suggest you the material which is self lubricating, tough and can be used for this application. No lubrication No dust.
It is "Metalon". You can get the details on internet.

Tom
 
Last edited by a moderator:
Well, if it can't be enclosed / sealed, how about rigging something up so that you have constant lubricant / water / oil spraying onto the rack-and-pinion?

EDIT: And welcome to PhysicsForums!
 
lot of rack and pinion steering boxes running on Baja off road series vehicles..got heavy duty " rubber" bellows to cut down on sand and dirt, rocks etc..you run into at 65 MPH racing thru the desert for 1000 miles...also check out mud bog racers who drive theri mosnter trucks thru mud pits and bogs for fun...insane but fun...
hot rodders are the last real innovators we got ...
 
This might sound incredibly simplistic, and might not be applicable, but have you thought about just mounting a toothbrush or similar device on a crank handle to scrape crap off of the rack on the back-stroke?
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'What type of toilet do I have?'

Thread 'What type of toilet do I have?'

I was enrolled in an online plumbing course at Stratford University. My plumbing textbook lists four types of residential toilets: 1# upflush toilets 2# pressure assisted toilets 3# gravity-fed, rim jet toilets and 4# gravity-fed, siphon-jet toilets. I know my toilet is not an upflush toilet because my toilet is not below the sewage line, and my toilet does not have a grinder and a pump next to it to propel waste upwards. I am about 99% sure that my toilet is not a pressure assisted...
View full post »

Thread 'Thread No-Go plug gage allows 3 turns to enter. That's too many!'

After over 25 years of engineering, designing and analyzing bolted joints, I just learned this little fact. According to ASME B1.2, Gages and Gaging for Unified Inch Screw Threads: "The no-go gage should not pass over more than three complete turns when inserted into the internal thread of the product. " 3 turns seems like way to much. I have some really critical nuts that are of standard geometry (5/8"-11 UNC 3B) and have about 4.5 threads when you account for the chamfers on either...
View full post »

Similar threads

Need an ME for a rack and pinion design, what is needed from both of us
Replies
5
Views
1K
Designing Rack and Pinion Gears: How Do I Calculate the Required Parameters?
Replies
2
Views
7K
I need help, please, designing a pool sensor for breaking . . .
Replies
2
Views
130
Spring+mass to do known job. How dimension? Impulse? Energy?
Replies
18
Views
2K
Limiting factor in design of small gas turbine w/ LOW self sustain speed
Replies
5
Views
2K
Rack and Pinion Calculation help
Replies
6
Views
3K
Rack and pinion, motor selection method
Replies
16
Views
21K
What is the optimal profile for a self reversing screw?
Replies
3
Views
8K
PID Control: Is Droop Always Against Setpoint?
Replies
3
Views
2K
How to Design the Complex Shapes of a Rotary Engine
Replies
30
Views
19K

Hot Threads

Recent Insights

Back
Top