What is the acceleration of two masses on pulleys with constant tension?

  • Thread starter Thread starter Karol
  • Start date Start date
  • Tags Tags
    Pulleys
AI Thread Summary
The discussion focuses on calculating the acceleration of two masses at the ends of a pulley system with constant tension. The equations derived indicate that the acceleration of the end masses is influenced by the number of middle masses, leading to the formula a = (N-2)/3 g. Participants highlight the importance of considering the balance of forces among the masses and the role of the ceiling in supporting the system. A key insight is that the end masses move down while the middle masses move up, demonstrating a lever effect. The conversation emphasizes the complexities of analyzing such systems and the need for careful consideration of forces involved.
Karol
Messages
1,380
Reaction score
22

Homework Statement


Snap1.jpg

All N+2 masses are m. what is the acceleration of the 2 masses at the ends.

Homework Equations


The rope on a weightless pulley has constant tension.

The Attempt at a Solution


The situation is the same as:
Snap2.jpg
$$\left\{\begin{array}{l} Nmg-2T=Nma \\ T-mg=ma \end{array}\right.$$
$$\rightarrow~a=\frac{N-2}{N+2}g$$
$$N=1\rightarrow~a=-\frac{1}{3}g$$
And it's wrong
 
Physics news on Phys.org
I wonder about your assumed equivalent system. Try the following thought experiment with the original system: Replace the two end masses with fixed supports so that the rope is fixed at those points and the system will be static. What would be the tension in the rope? Is it Nmg? Nmg/2? Something else?
 
Last edited:
If the accelerations of the end masses is a, kinematicly, what is the acceleration of each of the N middle masses?
 
I will denote as x and a the vertical displacement and acceleration of the 2 masses at the ends, and with y the displacement of each of the N middle masses:
$$2x=2Ny~~\rightarrow~~y=\frac{x}{N}~~\rightarrow~~\ddot y=\frac{a}{N}$$
$$\left\{\begin{array}{l} Nmg-2T=Nm\frac{a}{N} \\ T-mg=ma \end{array}\right.~~\rightarrow~~a=\frac{N-2}{3}g$$
 
Karol said:
I will denote as x and a the vertical displacement and acceleration of the 2 masses at the ends, and with y the displacement of each of the N middle masses:
$$2x=2Ny~~\rightarrow~~y=\frac{x}{N}~~\rightarrow~~\ddot y=\frac{a}{N}$$
$$\left\{\begin{array}{l} Nmg-2T=Nm\frac{a}{N} \\ T-mg=ma \end{array}\right.~~\rightarrow~~a=\frac{N-2}{3}g$$
That's not what I get. $$mg-2T=m\frac{a}{N}$$
 
Hi Karol. Instinctively it is tempting to think that the N masses must all contribute to the net force that the end masses experience. But if you look closely you'll see that by symmetry most of the N masses are balancing each other's contributions over the pulleys between them, and these upper pulleys are supported by the "ceiling". So in effect the "ceiling" is doing most of the "lifting".

I suggest that you focus on one general representative of the N masses to write your equation. I concur with @Chestermiller 's analysis.
 
  • Like
Likes Chestermiller
The positive direction is upwards, a, the edge's acceleration is positive and ay, the acceleration of the other masses is negative:
$$\left\{\begin{array}{l} 2T-mg=-ma_y=-m\frac{a}{N} \\ T-mg=ma \end{array}\right.~~\rightarrow~~a=-\frac{N}{2N+1}g$$
Not good, a<0.
 
Karol said:
The positive direction is upwards, a, the edge's acceleration is positive and ay, the acceleration of the other masses is negative:
$$\left\{\begin{array}{l} 2T-mg=-ma_y=-m\frac{a}{N} \\ T-mg=ma \end{array}\right.~~\rightarrow~~a=-\frac{N}{2N+1}g$$
Not good, a<0.
Surprisingly, this is actually correct. The two end masses move down, and all the other masses move up. This is a "lever" effect.
 
  • Like
Likes gneill
Thank you Haruspex and gneill. so only the 2 masses adjacent to the 2 outer masses contribute. the outer masses must hold half of the adjacent masses, ##\frac{1}{2}mg##, plus the acceleration of all the inner N mases
 
  • #10
Karol said:
Thank you Haruspex and gneill
You're welcome. But I think you meant to thank Chestermiller rather than Haruspex. Although Haruspex is often very helpful, too!
 
  • #11
Sorry, true... but thank you all...
 

Similar threads

Replies
5
Views
920
Replies
12
Views
1K
Replies
15
Views
6K
Replies
22
Views
6K
Replies
7
Views
1K
Replies
40
Views
4K
Replies
30
Views
3K
Replies
18
Views
807
Back
Top