What is the angular velocity of the two disks combined?

AI Thread Summary
The discussion focuses on calculating the angular velocity of two combined disks after one is dropped onto the other. The first disk has a mass of 1.6 kg and an initial angular velocity of 55 rad/s, while the second disk has a mass of 0.45 kg and is initially at rest. The conservation of angular momentum is applied, emphasizing the importance of considering the moment of inertia for each disk. The final angular velocity is calculated using the formula for rotational momentum, leading to a result of approximately 49.89 rad/s. The approach taken in the calculations is confirmed as correct by other participants in the discussion.
mastamind518
Messages
2
Reaction score
0

Homework Statement



A 1.6 kg disk with radius 0.63 m is rotating freely at 55 rad/s around an axis perpendicular to its center. A second disk that is not rotating is dropped onto the first disk so that their centers align, and they stick together. The mass of the second disk is 0.45 kg and its radius is 0.38 m. What is the angular velocity of the two disks combined?
rad/s

m1 = 1.6 Kg
r1 = 0.63 m
w1 = 55 rad/s
m2 = 0.45 Kg
r2 = 0.38 m


Homework Equations



conservation of angular momentum

L=mvr

v=rw

The Attempt at a Solution



i set up the equation as... (m1)(v1)(r1)=(m1r1 + m2r2)(v)

where v1 = r1w1 and v is equal to the linear velocity(which should be same for both?)

I solved for v, and then divided by r1, since that's the radius of the whole system, and got an answer of 47.02rad/s. The answer key says the answer is 50 rad/s...

which concept did i get wrong?
 
Physics news on Phys.org
Welcome to PF.

For rotational momentum don't you want to consider the Moment of Inertia of the disks and not just the mass?

For a solid disk I = 1/2*m*r2
 
LowlyPion said:
Welcome to PF.

For rotational momentum don't you want to consider the Moment of Inertia of the disks and not just the mass?

For a solid disk I = 1/2*m*r2

Thanks a lot for that tip...

So by using moment, i would have...

(Iinitial)(winitial) = (Ifinal)(wfinal)

(1/2)(m1)(r1)^2(w1) = (1/2)(m1(r1)^2+m2(r2)^2)(w2) where w2 is the final angular velocity

I get 49.89rad/s for w2...just wanted to confirm i was doing it right...
 
Last edited:
mastamind518 said:
Thanks a lot for that tip...

So by using moment, i would have...

(Iinitial)(winitial) = (Ifinal)(wfinal)

(1/2)(m1)(r1)^2(w1) = (1/2)(m1(r1)^2+m2(r2)^2)(w2) where w2 is the final angular velocity

I get 49.89rad/s for w2...just wanted to confirm i was doing it right...

Without calculating it out, that looks like the right approach.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top