What Is the Force Threshold for Beam Bending?

AI Thread Summary
The discussion focuses on calculating the bending moment of a beam and determining the force threshold at which it begins to bend. A participant mentions that the beam will start bending with any force greater than zero but seeks a specific formula for precise calculations. Another contributor emphasizes the need for more details to provide accurate feedback and references the concept of beam deflection. The section modulus Z has been calculated as 9.48, which is relevant for determining the bending stress. Understanding these calculations is crucial for assessing beam performance under load.
barvas11
Messages
32
Reaction score
0
Hi Guys,
Do you know of any short formula to calculate bending moment of the beam on the attached image?
I need to know the force at which this beam will start bending.
 

Attachments

  • BEAM BENDING.png
    BEAM BENDING.png
    7.7 KB · Views: 539
Engineering news on Phys.org
The beam will start bending as soon as the force is more than zero.

You're going to have to be more specific if you want more feedback. Have you looked into how beam bending calculatinos are done?
 
I know that the beam will deflect but it will flex back up to the certain point. I am trying to determine the force at which the beam will bend and deform.

I have managed to calculate the section modulus Z that is 9.48
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Find 3D Printer & Software Resources for Prototype Creation'

I'd like to create a thread with links to 3-D Printer resources, including printers and software package suggestions. My motivations are selfish, as I have a 3-D printed project that I'm working on, and I'd like to buy a simple printer and use low cost software to make the first prototype. There are some previous threads about 3-D printing like this: https://www.physicsforums.com/threads/are-3d-printers-easy-to-use-yet.917489/ but none that address the overall topic (unless I've missed...
View full post »

Similar threads

What is bending moment? Is it a moment couple? Why?
Replies
9
Views
3K
Calculating the bending stress of a simply supported beam
Replies
5
Views
6K
Calculate the residual stress on a beam after bending
Replies
30
Views
7K
Sign convention of internal forces in vertical bars for bending moment
Replies
5
Views
3K
Shock absorber forces
Replies
4
Views
2K
How Do Horizontally Oriented Gussets Perform in Cantilever Bending?
Replies
36
Views
5K
Bending moments about two different axes
Replies
11
Views
3K
How Do I Select the Right Steel I-Beam for Increased Load Requirements?
Replies
1
Views
2K
Plastic bending - analytical calculations
Replies
2
Views
2K
Bending a beam from straight to an arc with axial force
Replies
7
Views
2K

Hot Threads

Recent Insights

Back
Top