What is the mass of the meter stick?

  • Thread starter Thread starter Quipzley
  • Start date Start date
  • Tags Tags
    Mass Meter
AI Thread Summary
The meter stick balances at the 50.0 cm mark with two 5.00 g coins stacked at the 12.0 cm mark, shifting the balance to 45.5 cm. The discussion focuses on calculating the mass of the meter stick using torque principles, where equal torques on both sides must be established. The torque created by the weight of the coins and the stick's center of mass is analyzed to find the mass. The calculated torque from the coins is balanced by the torque from the meter stick's mass. Ultimately, the mass of the meter stick is determined to be 74.4 g.
Quipzley
Messages
8
Reaction score
0
A meter stick blances horizontally on a knife-edge at the 50.0 cm mark. With two 5.00 g coins stacked over the 12.0 cm mark, the stick is found to balance at the 45.5 cm mark. What is the mass of the meter stick?

I know it is going to be having equal torques. The torque on one side should be .01 kg*9.8 m/s^2* .335 m = .03283 N*m + the torque of the .335 m of meter stick. The other side is just the torque of the .455 m of stick. I'm not sure how to calculate the torque of the meter stick.
 
Physics news on Phys.org
The answer is supposed to be 74.4 g.
 
Pick a point, any point, and sum moments to zero. Define your variables; mass of stick and coins, ms and mc; forces, a, b, and g. Solve for ms.
 
Quipzley said:
A meter stick blances horizontally on a knife-edge at the 50.0 cm mark. With two 5.00 g coins stacked over the 12.0 cm mark, the stick is found to balance at the 45.5 cm mark. What is the mass of the meter stick?

I know it is going to be having equal torques. The torque on one side should be .01 kg*9.8 m/s^2* .335 m = .03283 N*m + the torque of the .335 m of meter stick. The other side is just the torque of the .455 m of stick. I'm not sure how to calculate the torque of the meter stick.

The stick's centre of mass experiences a weight force mg, (50.0 - 45.5) cm from the knife-edge, producing a torque of mg(0.045 m). This torque is balanced by the torque of the coins (0.01000 kg)g(0.335 m) = mg(0.045 m). Therefore m = 74.4 g.
 
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Trying to understand the logic behind adding vectors with an angle between them'
My initial calculation was to subtract V1 from V2 to show that from the perspective of the second aircraft the first one is -300km/h. So i checked with ChatGPT and it said I cant just subtract them because I have an angle between them. So I dont understand the reasoning of it. Like why should a velocity be dependent on an angle? I was thinking about how it would look like if the planes where parallel to each other, and then how it look like if one is turning away and I dont see it. Since...
Back
Top