What is the work done by the two tugs pulling a tanker?

  • Thread starter Thread starter mjcowley
  • Start date Start date
  • Tags Tags
    Work Work done
AI Thread Summary
Two tugs are pulling a tanker with forces of 1,400,000 N each, angled 14 degrees west and east of north, respectively, over a distance of 0.66 km. The initial calculation for work done was incorrect due to unit conversion errors, as the distance was mistakenly treated in meters instead of kilometers. The correct approach involves ensuring the distance is converted to meters for accurate calculations. The resultant force from both tugs was calculated as 2,716,828 N, leading to a work done calculation of approximately 1.79 million Nm. Attention to unit consistency is crucial for solving physics problems accurately.
mjcowley
Messages
2
Reaction score
0

Homework Statement



Two tugs pull a tanker. Each at a force 1400000N with one at an angle 14degrees west of north, the other 14degrees east of north. They pull the tanker 0.66km north.

Homework Equations



W=Fs

The Attempt at a Solution



I simply took the vector force of 1 tanker

1400000Cos(14) = 1358414N multiplied it by two for both tugs = 2716828

Therefore W (asked in 3 sig figs) = 2716828*0.66 = 1.79*10^6Nm

Unfortunately I'm told this is wrong :frown:

Appreciate any help!
 
Last edited:
Physics news on Phys.org
You forgot the distance!
 
mjcowley said:

Homework Statement



Two tugs pull a tanker. Each at a force 1400000N with one at an angle 14degrees west of north, the other 14degrees east of north. They pull the tanker 0.66km north.

Homework Equations



W=Fs

The Attempt at a Solution



I simply took the vector force of 1 tanker

1400000Cos(14) = 1358414N multiplied it by two for both tugs = 2716828

Therefore W (asked in 3 sig figs) = 2716828*0.66 = 1.79*10^6Nm

Unfortunately I'm told this is wrong :frown:

Appreciate any help!


Look at your units.
 
Doc Al said:
You forgot the distance!
OK... you put in the distance (good!), but the distance is measured in km, not meters.
 
lylos said:
Look at your units.

Good ol MKS

Thanks for that :)
 

Thread 'Rolling without slipping on a curved surface'

Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
View full post »
Thread 'Voltmeter readings for this circuit with switches'

Thread 'Voltmeter readings for this circuit with switches'

TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
View full post »

Similar threads

Work done on an Object - Pulling a wagon while lifting up at an angle
Replies
1
Views
2K
The Work Done in Pulling a Supertanker
Replies
4
Views
14K
How much work is done on a bucket when pulling it up?
Replies
3
Views
2K
Work Done by Elevator Cable in Sample Problem 7-6
Replies
2
Views
3K
How to Determine the Work Done by the Rope on a Sledge?
Replies
5
Views
2K
How Much Work Is Done When Pulling a Sled at an Angle?
Replies
3
Views
2K
Calculating Work Done by a Child Pulling a Toy Car
Replies
2
Views
938
How Much Work Is Done Pulling a Wagon at an Angle?
Replies
1
Views
2K
What should be the work done here?
Replies
9
Views
2K
Finding the WORK done by a crane in lifting a load
Replies
14
Views
8K

Hot Threads

Recent Insights

Back
Top