What is this piece of equipment?

  • Thread starter Thread starter Fezziwig
  • Start date Start date
  • Tags Tags
    Equipment
AI Thread Summary
The discussion centers around the identification and use of pipettes, specifically a type that measures small volumes of liquid. The pipettes in question are approximately 34 cm long and feature a calibration marking of T.D. 20°C, indicating their accuracy at room temperature. The orange end, which is typically detachable, is meant to connect to a bulb or a scroll wheel handle used for drawing liquid into the pipette. The conversation highlights that these pipettes are less precise compared to higher-quality models designed for specific volumes. While older methods involved manual suction and control, modern practices have shifted towards plastic alternatives for convenience. The original poster, Fezziwig, is considering selling the pipettes and seeks to provide a more accurate description to enhance their value.
Fezziwig
Messages
14
Reaction score
1
xlyob9s.jpg


As a gift I received 25 of these things (the previous owner not knowing what they were). They're aprox 34cm in legnth. The orange bit is closed and doesn't detach, so I can't find any uses for it. The writing on it above the calibration reads...

T.D. 20°C
10ml x 0.1

Regardless of their use I will most likely be selling them and I'd imagine they sell for more if I had a real description. If you want one or more I'll be sure to give you a discount.

Thanks,
Fezziwig.
 
Chemistry news on Phys.org
Those are called pipettes. They are used to measure small volumes of solutions, for example. The 20 degrees C marking means they are accurate for work with solutions near room temperature.
 
The orange bit should be able to detach. That end is meant to be attached to a bulb or "scroll wheel" handle (not sure what their actual name is, but they have a wheel you rotate with your thumb to draw liquid into the pipette).
 
Right, Thanks guys. So they would probably need that scroll wheel thing to be of any use. Thinking about it now, I have seen these things before.
 
In the old days, :rolleyes: mnyah mnyah, you just sucked up the liquid into the pipette, you were expected to use common sense and the school or college didn't fill forms and have health and safety inspectors to supervise, you put a finger over the top, and with finger control let liquid slowly descend to the desired mark flowing back into the original container, then you moved to wher you wanted to put your x ml and let it flow out to the other desired mark, or you could let it all flow out and there was a story about drainage time and the last drop etc.

Pipettes with marks on like yours were for the less precise work, for more precise you had higher quality pipettes that delivered only one volume.

For the less precise work they tended to be phased out for plastic 'eppendorf' thumb push things, but these are not so convenient for the larger volumes and I guess things like your pic are still used?

Maybe you are not a scientist, otherwise throws me that anyone doesn't recognise them.
 
Just to clarify, this is what I was referring to-

e_profill_406.jpg


http://www.socorex.com/manual-pipette-fillers-profiller-en-1-1-13-140.html
 
I want to test a humidity sensor with one or more saturated salt solutions. The table salt that I have on hand contains one of two anticaking agents, calcium silicate or sodium aluminosilicate. Will the presence of either of these additives (or iodine for that matter) significantly affect the equilibrium humidity? I searched and all the how-to-do-it guides did not address this question. One research paper I found reported that at 1.5% w/w calcium silicate increased the deliquescent point by...
I was introduced to the Octet Rule recently and make me wonder, why does 8 valence electrons or a full p orbital always make an element inert? What is so special with a full p orbital? Like take Calcium for an example, its outer orbital is filled but its only the s orbital thats filled so its still reactive not so much as the Alkaline metals but still pretty reactive. Can someone explain it to me? Thanks!!
I'm trying to find a cheap DIY method to etch holes of various shapes through 0.3mm Aluminium sheet using 5-10% Sodium Hydroxide. The idea is to apply a resist to the Aluminium then selectively ablate it off using a diode laser cutter and then dissolve away the Aluminium using Sodium Hydroxide. By cheap I mean resists costing say £20 in small quantities. The Internet has suggested various resists to try including... Enamel paint (only survived seconds in the NaOH!) Acrylic paint (only...

Similar threads

2
Replies
52
Views
7K
Replies
16
Views
3K
Replies
3
Views
3K
Replies
13
Views
3K
Replies
1
Views
4K
Replies
5
Views
3K
Replies
1
Views
3K
Back
Top