Ideas for a Basic RLC Related Class Project

AI Thread Summary
A college sophomore in electrical engineering is seeking ideas for a simple RLC circuit project that can be built using components from stores like RadioShack. They are looking for projects that include a capacitor and inductor, ideally with clear diagrams and labeled components. Suggestions include building a band pass or band reject filter, or an AM radio kit, which would help explain the role of adjustable inductors and capacitors. The discussion also touches on quiz questions related to the input impedance of RLC circuits. The user has found additional resources and is optimistic about finding suitable project ideas.
mushiman
Messages
10
Reaction score
0
I've been a lurker for a longtime (and recently made an account).

That aside, I've just started my sophomore level classes in electrical engineering this year (in college obviously), and my instructor has asked us at the last minute to make a simple project involving an RLC network (so basically, anything incorporating a capacitor and inductor). I've been digging through these forums and have done some Googling for an idea for a project, but I haven't found anything that could work for my situation.

We were literally told to just pickup a kit from RadioShack or something of that nature, build it, and explain exactly what the circuit is doing and why it's doing it [in class]. Unfortunately, stores such as RadioShack have the components for the task, but not the full kits with ready-made diagrams.

Does anyone have any links to websites that have these types of projects available? A diagram with the needed components labeled/listed is enough -- I haven't had much success locating one. This should not be a large project; simply large enough to consume a few hours of my time and fit on one breadboard.

I'm not really particular on the what the circuit should do, so if anyone has any ideas, I'd be happy to hear them. Thanks.
 
Engineering news on Phys.org
How about building a simple band pass or band reject filter? Those are pretty basic and you can find loads of information on line for it.
 
Here's a good kits website:

http://www.rainbowkits.com/kits/kits1.html

Or you can google electronics kits to get lots of other hits. I'd recommend getting an AM radio kit, and explaining why there are adjustable inductors and caps in the input circuit. That's really at the core of what RLC circuits are used for.

Quiz questions -- what is the input impedance of a parallel RLC circuit versus frequency? What is the input impedance of a series RLC circuit versus frequency?

An alternative would be to look at the equivalent RLC circuit of a crystal, and explain how that works in a crystal oscillator circuit. But that's a lot more advanced, and maybe best left for next year...
 
Thanks for the replies.

I did some searching for both of your project ideas and there appears to be plenty of information on the two. I'll try rainbowkits.com again later, as they seem to be down at the moment.

I also stumbled upon Jameco again (forgot about them), and they seem to have numerous kits, so I think I'll have plenty of ideas to run with now.

Thanks again for the ideas, I'll post back with more questions if need be.
 
Sounds like you're on top of it mushiman. But what about the quiz questions?
 
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Back
Top