Automotive Air compression firing mechanism

AI Thread Summary
A high school student is seeking guidance on designing an air cylinder to fire seed pellets from a drone at specific intervals with enough pressure for soil embedding. The discussion highlights the need for a mechanism, possibly involving an electric valve to control pellet release timing. Participants express caution about providing direct solutions, emphasizing the importance of independent research on existing mechanisms. The conversation encourages evaluating various options to determine the most suitable approach for the project. Overall, the focus is on combining creativity with practical engineering principles for effective design.
Asad Raza
Messages
81
Reaction score
3
Hello,
I am high school student working on a project to design an air cylinder, which would fire seed pellets from the drone at specific time intervals with sufficient pressure to embed them into the soft soil.
I looked up on the Internet about airguns and other stuff but couldn't find anything very much relevant. Would be very grateful if anyone could help.
 
Engineering news on Phys.org
russ_watters said:
What, specifically, are you asking for help with?
Someone may want to outline a general mechanism and the equipment needed (an electric valve maybe to open and close after each second to drop the pellets possibly)
 
Asad Raza said:
Someone may want to outline a general mechanism and the equipment needed (an electric valve maybe to open and close after each second to drop the pellets possibly)
You haven't found any good mechanisms like that? I'm hesitant to hand you something you could/should research on your own. Part of your project should be looking at multiple common mechanisms and evaluating them for the best one to apply to your needs.
 

Thread 'Race car suspension Class'

Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Cantilever help'

I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
View full post »

Similar threads

Automotive How can heat management be optimized in compressed air powered bikes?
Replies
3
Views
6K
A Non-quasi-static Air Compression Calculation
Replies
6
Views
1K
Air Pressure Equalization Between 2 Vessels
Replies
6
Views
9K
What Are the Key Design Features of Reciprocating Compressed Air Engines?
Replies
1
Views
5K
Seal friction needed for pneumatic/hydraulic piston
Replies
5
Views
3K
Question about cooling due to expansion of compressed air
Replies
16
Views
17K
Automotive Air fuel ratio effects in diesel vs. petrol engines
Replies
11
Views
22K
Could a Reverse Uni-Flow Engine Revolutionize the Automotive Industry?
Replies
4
Views
5K
How Can We Design a Compressed Air Car for 300 km Travel?
2
Replies
82
Views
27K
B Energy Efficiency of Compressed-Air-Powered Parabola Riding Vehicle?
4
Replies
169
Views
14K

Hot Threads

Recent Insights

Back
Top