Box Pushed Up an Incline Ramp: Basic Newton's Law Questions

AI Thread Summary
A 90 kg box is pushed up a frictionless ramp inclined at 28° with a constant speed, requiring a calculated applied force of 414N. When friction is introduced with a coefficient of 0.18, the force of kinetic friction (Fk) is determined to be approximately 158.76N. The total applied force in this scenario combines the gravitational component along the ramp and the frictional force, resulting in 572N. The discussion emphasizes the importance of accurately representing the normal force (FN) in relation to the gravitational forces acting on the box. Correctly identifying the forces is crucial for solving the problem effectively.
Kathy W
Messages
4
Reaction score
0

Homework Statement


A 90 kg box is pushed by a horizontal force F at constant speed up a ramp inclined at 28°, as shown. Determine the magnitude of the applied force.
  1. when the ramp is frictionless.
  2. when the coefficient of kinetic friction is 0.18
upload_2015-7-22_11-43-55.png

Homework Equations


F=mg
FN=mg
μ= Fk/FN

The Attempt at a Solution


a) mg=(90)((.8)= 882N=Fg

sin28=Fgx/882N
(0.469)(882)= Fgx
414N=Fgx= magnitude of applied force

b) FN=mg= 882N
μ=Fk/FN
0.18=Fk/882
(882)(0.18)= Fk
Fk= 158.76

** This is where I am unsure of my approach**

Fapplied= Fgx+Fk
=414N+158.76 N
= 572N

That seems like too much to me, but I'm not quite sure. Does it look like I have that equation correct ,or am I supposed to subtract the value I found for Fk from FgX, or something totally different. Any help would be very much appreciated
 
Physics news on Phys.org
Kathy W said:
FN=mg= 882N
μ=Fk/FN
0.18=Fk/882
(882)(0.18)= Fk
Fk= 158.76

You have not drawn FN correctly . Redraw correctly and try again .

Hope this helps .
 
Qwertywerty said:
You have not drawn FN correctly . Redraw correctly and try again .

Hope this helps .
oh okay, is it opposing the Fy aspect instead of Fg? I was confused when I was drawing that! Thank you for your response
 
Kathy W said:
oh okay, is it opposing the Fy aspect instead of Fg? I was confused when I was drawing that! Thank you for your response
Yes. The normal force opposes that component of gravity which would cause acceleration perpendicular to the surface ( the incline plane).
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top