Calculating Gforce of Impact from 3ft Fall

  • Thread starter Thread starter Cryptic edge
  • Start date Start date
  • Tags Tags
    Impact
AI Thread Summary
The discussion revolves around calculating the g-force experienced from a 3-foot fall impacting a toe against a tile floor. The individual, weighing 220 lbs, seeks to understand the g-force of this impact, noting the severe pain and inability to walk afterward. It is highlighted that precise calculations of g-force require detailed information about the impact duration, as a quick stop can imply an infinite force, which is unrealistic. A rough estimate suggests a peak force of approximately 2.4g based on assumed conditions. The inquiry reflects a broader interest in understanding the forces involved in such impacts and their potential for injury.
Cryptic edge
Messages
4
Reaction score
0
Ok, so this isn't exactly homework, but it seems the most appropriate spot to post this.

A few days ago I (a 220 lb individual) hit an impact from a fall from 3 ft of my entire weight on a single toe against an unmovable object (tile floor)

I'd like to know the gforce of that impact, assume I came to a full stop nearly immediately

I'd also like to know the gforce of a 30 lb object impacting from 3 ft against a slightly padded object, quick stop though (for comparison with someone who thought I was out of line for getting an X-ray when I couldn't walk after for over a day, who used that as a line of reasoning object impacted a showed foot in this scenario, initial scenario was a bare foot with all force against big toe)

I appreciate any help calculating this that can be given.
 
Physics news on Phys.org
We get this question all the time, in different guises. The short answer is that you cannot know without further, detailed information.
You do know the momentum change to be undergone, but that is the integral of force over time. The longer the time the impact is spread over, the lower the peak force can be. An instant stop would imply an infinite force, which clearly never happens.
In the case of your toe, your toe would have come to a stop in much less time than the rest of you. Suppose the whole process took half a second, and the force rose linearly to a peak then fell away linearly at the same rate to 1000N over that time. Your momentum change was 100kg * √(2*9.8) m/s = 443 kg m/s. If I've calculated correctly, that gives a peak of 2358N, or 2.4g.
 
Ah. I know when it happened the impact seemed to be an instant stop and the damage to the foot was enough the doc had to double check the X-rays for a break after looking at the bruising. It was a curiosity what the gforce it took to cause that level of bruising since it was enough that made me unable to walk for a day.

I thank you for the help :) I know exact wouldn't have been possible without a lot of precise measurements anyway and that's not something I'm willing to recreate and get those kind of measurements for what amounts to be curiosity. (plus next time I may not be so lucky that it doesn't break lol)
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top