Calculating torque when the lever arm has mass

AI Thread Summary
The discussion revolves around calculating the torque on a board supported by scaffolding when a man stands on it. The board weighs 15 kg and the man weighs 70 kg, and the goal is to determine how far the man can stand before the board tips over. The initial approach involved using calculus to derive the torque, but it was pointed out that a simpler algebraic method could suffice. The tipping point occurs when the reaction force at the right support becomes zero, which happens when the man stands approximately 0.27 m from the left support. The conversation highlights the importance of understanding the center of mass and equilibrium conditions in torque calculations.
threecorners
Messages
2
Reaction score
0

Homework Statement


A board is set on top of a scaffolding, with dimensions as shown in the diagram. The board weighs 15 kg. A man weighing 70 kg stands on the board as shown. How far out can he stand before the board falls?

96FJw.png


Homework Equations


Torque: \tau = rFsin(\theta)
Force due to gravity: F = mg


The Attempt at a Solution


I decided to use calculus, and then combine with the torque equation for the torque the man applies. I am assuming the leftmost point where the scaffolding touches the board is the fulcrum, and the rightmost point only serves to keep the board from rotating clockwise.

First, since gravity is our only force and it points downwards, we have \tau=rmg.
Now we use calculus:
d\tau=rg\cdot dm, and dm=\frac{15}{5.5}\cdot dr, so
d\tau=\frac{15g}{5.5}r\cdot dr.

Now I assume the first 1.5m of board on each side of the fulcrum cancel out, so the torque on the right of the fulcrum is \tau=\int_{1.5}^{4} \frac{15g}{5.5}r\cdot dr=...=18.75g. I leave the g because I am about to cancel it out.

Now for the lefthand side of my equation, i just need the torque from the man, which will be at a distance of x out, which we must solve for. So
x\cdot 70\cdot g = 18g, and so x\cong 0.27m.

Okay, that's it for my solution. The book says the answer should be 1.2m. I haven't done physics in a while but I have done a lot of math, which is why my solution is overly mathy. I assume there's an easier thing to do here that doesn't require calculus like I did...
 
Physics news on Phys.org
Your answer is correct, but try to avoid using calculus when algebra will suffice. The 15 kg mass of the board can be represented by a 15g force acting at the center of mass of the board, that is, acting dead center at 1.25 m from the fulcrum. Thus, 70x = 15(1.25), solve x = .27 m.

I am not sure if you realized that tipping occurs when there is no reaction force at the right support as the board starts to lift off from it.

Looks like the book messed up big time on this one, maybe a calculus error:biggrin:

Wecome to PF!
 
Thank you so much, PhanthomJay! Yeah, wrong answers in a book can really make you question yourself... and yes, center of mass was the magic thing I needed, thanks! One question, what do you mean by:

I am not sure if you realized that tipping occurs when there is no reaction force at the right support as the board starts to lift off from it.

...And thanks again!
 
Supposing the guy walks less than 0.27 m from the left support, say 0.1 m. The system is still in equilibrium, so when you sum moments about the left support equals 0, you will find there must be an upward reaction force at the right support in order to satisfy this equilibrium condition. As the guy moves further away, this reaction force at the right support gets lower and lower, becoming 0
when the guy has moved .27
m. That's the tip point. If he were to continue walking a hair further away, the system could no longer be in equilibrium, since the support reaction at the right can't be less than zero, and the plank would fall over, taking Johnny with it. Unless the plank was nailed down to the support, but it is stated that this is not so.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...

Similar threads

Back
Top