Calculation of equivalent resistance

AI Thread Summary
The discussion focuses on calculating the equivalent resistance between points P and Q in a given circuit diagram. The original poster attempted to solve the problem but arrived at an incorrect answer of (11/10) R, expressing confusion about identifying resistors in series and parallel. Participants suggest numbering the resistors and simplifying the circuit by eliminating unnecessary wires to clarify the configuration. They emphasize the importance of showing detailed workings to identify mistakes and provide accurate guidance. The conversation highlights the need for clear identification of resistor arrangements to solve equivalent resistance problems effectively.
Arka420
Messages
28
Reaction score
0

Homework Statement

: [/B]Given the circuit diagram, find the equivalent resistance between points P and Q.
ngodxd.png

Homework Equations

: [/B]ΔVloop = 0, ΔIjunction = 0 and V = IR

The Attempt at a Solution

: [/B]Eliminating the wires with no resistors and solving for resistance gives me the answer as (11/10) R, which is not the answer. I'm confused as to which resistors are in parallel and which resistors are in series.
 
Last edited by a moderator:
Physics news on Phys.org
Perhaps start by numbering the resistors A, B, C etc and post the drawing again.

Tell us which you think are in series or parallel. For example "I think A is in series/parallel with..."

Normally this type of problem is simplified by replacing two resistors in series or parallel with one and redrawing the circuit. You've posted the original so show us the first step/simplification that you made.
 
Arka420 said:

Homework Statement

: Given the circuit diagram, find the equivalent resistance between points P and Q.
ngodxd.png
[/B]

Homework Equations

: ΔVloop = 0, ΔIjunction = 0 and V = IR[/B]

The Attempt at a Solution

: Eliminating the wires with no resistors and solving for resistance gives me the answer as (11/10) R, which is not the answer. I'm confused as to which resistors are in parallel and which resistors are in series. [/B]
Post your working out. We have no way of knowing where you went wrong (and therefore how to help you/ correct any mistakes) if we can't see your reasoning, but the attempt at the problem appears to be right (eliminate the short wire and simplify using the rules for resistors in series/ parallel).
 
Remember also the rule that if multiple resistors have the same voltage drop associated with them then they are parallel
 
This is how I worked out the circuit. Is it correct?
24ex442.png
 
Arka420 said:
This is how I worked out the circuit. Is it correct?
24ex442.png
Not correct.

Follow this advice:
CWatters said:
Perhaps start by numbering the resistors A, B, C etc and post the drawing again.

Tell us which you think are in series or parallel. For example "I think A is in series/parallel with..."
 

Thread 'Errors and significant figures'

I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
View full post »
Thread 'Collision of a bullet on a rod-string system: query'

Thread 'Collision of a bullet on a rod-string system: query'

In this question, I have a question. I am NOT trying to solve it, but it is just a conceptual question. Consider the point on the rod, which connects the string and the rod. My question: just before and after the collision, is ANGULAR momentum CONSERVED about this point? Lets call the point which connects the string and rod as P. Why am I asking this? : it is clear from the scenario that the point of concern, which connects the string and the rod, moves in a circular path due to the string...
View full post »
Thread 'A cylinder connected to a hanging mass'

Thread 'A cylinder connected to a hanging mass'

Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
View full post »

Similar threads

Find the equivalent resistance of this circuit
Replies
31
Views
4K
Is This a Series or Parallel Circuit?
Replies
13
Views
895
How can I calculate the equivalent resistance of this circuit?
Replies
9
Views
2K
Equivalent resistance of a circuit
Replies
3
Views
2K
Finding potential at a point in capacitor
Replies
2
Views
2K
Total equivalent resistance of a combined circuit
Replies
7
Views
2K
How to Calculate Equivalent Resistance and Current in a Simple Circuit Problem?
Replies
16
Views
2K
Platinum resistance thermometer and Kirchoff's Laws
Replies
1
Views
3K
Calculate the equivalent resistance
Replies
11
Views
2K
Finding the Current in a circuit
Replies
6
Views
3K

Hot Threads

Recent Insights

Back
Top