Can I Measure Total Pressure with a Thin Pipe Instead of a Pitot Tube?

AI Thread Summary
Using a thin pipe instead of a pitot tube to measure total pressure is feasible, as long as the pipe is smooth and faces the flow correctly. However, accuracy may be compromised compared to a traditional pitot tube, which is designed specifically for such measurements. The discussion highlights the importance of understanding whether total pressure or dynamic pressure is the desired measurement, especially when assessing flame speed. The user intends to avoid exposing their pitot tube to the flame while still obtaining accurate measurements. Overall, a thin steel tube can serve as an alternative for measuring total pressure in this context.
yangshi
Messages
19
Reaction score
0
Since pitot tubes measure total pressure from the flow ramming into the total pressure hole, could I use any thin piece of pipe facing the flow (given that it's smooth on the inside) to measure total pressure? Trying to think of ways not to use my pitot tube to measure the total pressure of a flame. Thanks!
 
Engineering news on Phys.org
Normaly there is no flow in a pitot tube, so the smooth schould be in the opening of the tube.
It's just a question of accurasy in the messure.

Is it really the total pressure you want ?
A typical pitot tube are used to result in the dynamik pressure whitch gives you speed / flow of the fluid messured.
 
Thanks for the reply. So OK, I'll use a thin steel tube then. And yes, I'm trying to find the flame speed and have a static port set up, but I don't want to expose my pitot tube to the flame.
 
That's right, take care of the instruments.
 
volu-probe-pitot-airflow-measurment-traverse-probe.png


http://www.airmonitor.com/products/volu-probe-traverse-probes/
 
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Thread No-Go plug gage allows 3 turns to enter. That's too many!'

After over 25 years of engineering, designing and analyzing bolted joints, I just learned this little fact. According to ASME B1.2, Gages and Gaging for Unified Inch Screw Threads: "The no-go gage should not pass over more than three complete turns when inserted into the internal thread of the product. " 3 turns seems like way to much. I have some really critical nuts that are of standard geometry (5/8"-11 UNC 3B) and have about 4.5 threads when you account for the chamfers on either...
View full post »

Similar threads

Pitot Tube will not measure stagnation pressure
Replies
22
Views
7K
Pressure measurement using a Piezometer
Replies
9
Views
4K
Bernoulli equation and parallel pipe branch
Replies
31
Views
4K
Pitot Tube Experiment: Measuring Pressure & Velocity
Replies
6
Views
14K
How to measure pulsations in a tube?
Replies
10
Views
2K
Measuring the total pressure of a centrifugal compressor
Replies
1
Views
2K
Modeling Air Compression Cylinder
Replies
45
Views
5K
Pitot Tubes and Static Pressure
Replies
1
Views
2K
How Accurate Is Using a DIY Pitot Tube to Measure Vacuum Pump Airflow?
Replies
8
Views
15K
Measuring Stagnation Pressure with a Manometer
Replies
9
Views
3K

Hot Threads

Recent Insights

Back
Top