Detanglers for copper wire/power lines - Do they exist?

AI Thread Summary
The discussion centers on the design of a vertical axis wind turbine (VAWT) featuring a contra-rotating mechanism, with a focus on managing power cables that may tangle during operation. The user is exploring the use of slip rings for electrical connections but is concerned about potential energy loss and maintenance issues due to friction and brush wear. They propose using gallium as a liquid metal alternative for connections to minimize wear, while also detailing their innovative design that incorporates magnetic bearings and dual squirrel cage turbines for enhanced efficiency. The user seeks advice on optimizing their design and addressing challenges related to stability and maintenance. Overall, the conversation highlights the complexities of integrating electrical engineering solutions into wind turbine design.
Jimmerding
Messages
3
Reaction score
0
Morning all,

I am currently designing a VAWT and am working on a contra-rotating turbine, but I am extremely new to electrical engineering as a whole, I just really like the idea of designing something like this as a fun project and possibly being able to benefit from lower power bills as a result!

The problem I am facing comes from the winding motion of the permanent magnets and my need to have power cables trailing down through a base. If I have just normal wiring, it will eventually start winding too tightly and need to spring back the other way. I've tried googling some sort of "detangler" device that will work for power cables, but have only found ones for telephone cables in call centers. Can anybody point me in the direction of something like this they know exists or perhaps a simple engineering solution that I am missing?

Thanks.
 
Engineering news on Phys.org
slip rings
 
  • Like
Likes davenn
Nidum said:
slip rings

Perfect! Thanks for that.

As you can probably tell, I am an extreme layman! Is there any sort of volt/amp loss due to the process of a slip ring? metal/graphite plates grinding against another metal plate to pass current through seems like there is a lot of potential for energy to be lost, and do you know whether there would be significant friction in a slip ring? my VAWT is using magnetic bearings and I am trying to keep any mechanical friction to an absolute 0. Also, looking at it there is "brush wear" meaning parts have to be monitored and replaced once in a while, I'm trying to make my VAWT very low maintenance.

Could I not replace the "connection" with something like gallium? a liquid metal at 29 degrees C, whilst still being able to conduct current fine. Wouldnt need a huge quantity of it either, just enough to fill the chamber...
 
Properly designed slip rings can be very efficient .

Tell us more about your design ideas .
 
Nidum said:
Properly designed slip rings can be very efficient .

Tell us more about your design ideas .

Well, it involves taking elements/ideas from direct drive turbines, magnetic bearing generators and contra rotation generators. imagine one tall squirrel cage style turbine (at this stage, just imagine the cylinder with the blades,nothing else), suspended by magnetic bearings so that minimal wind power is needed to turn it and it carries on spinning for a significant amount of time even after a gust of wind has blown. I would be aiming for overkill magnetic bearings using relatively cheap neodymium magnets to "lock" the spinning turbines in place and correct any buck/sway from strong winds.

I then split that in half through the middle,so you've essentially got 2 squirrel cages on top of each other. Rotate the blades to face the opposite way, and ideally,you would have 2 turbines spinning much the same speed in the opposite way from each other. Now imagine inside the cylindrical squirrel cage, you had an ultra light weight frame attached to each turbine, one houses your stator coils etc, the other houses your magnets and such like. Obviously I need a slip ring set up that allows for an element of pitch/pivot as well as spin - as mentioned before, there will be sway and wobble in strong winds using magnetic bearings. This slip ring set up would allow contra rotation of generator parts directly attached to the turbine. I feel that whilst VAWT have their efficiency flaws, what with half the blades working somewhat against the blades being pushed against by wind, this design would create fairly high relative RPM.

This design is still completely in my head / scribbled on a few bits of paper. for all I know, electro magnets might be a better system for the bearings as you could increase the pull on a certain spot to correct any wobbling, but that would make it a far more complicated design... Do you have any ideas?
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...

Similar threads

Replies
72
Views
20K
Replies
3
Views
1K
Replies
4
Views
2K
Replies
15
Views
4K
Replies
3
Views
2K
Replies
36
Views
4K
Replies
2
Views
2K
Back
Top