Does a balloon's temperature increase when a balloon is popped?

AI Thread Summary
When a balloon is popped, the temperature of the air inside often increases slightly, as observed in experiments where it rose from 29 to 29.2 degrees Celsius. This phenomenon may occur because the increase in volume when the balloon bursts can outweigh the decrease in pressure, as per the Ideal Gas Law. The results showed a consistent temperature increase of about 0.2-0.3 degrees Celsius, though variations in balloon composition and experimental conditions could affect accuracy. The discussion emphasizes the importance of measuring mean and standard deviation to assess the significance of temperature changes. Overall, the thermodynamic processes at play suggest that the work done on the gas during the popping contributes to this temperature rise.
Elizabeth Lil
Messages
2
Reaction score
0

Homework Statement


We blew up a balloon, attached a data logger inside the balloon. We then popped it and checked if the temperature increased or decreased. Most of the time, the temperature increased (from around 29 degrees Celsius to 29.2 degrees Celsius).

Why is this so?


Homework Equations


Ideal Gas Law: Pv= nRT (where n and R are constants)


The Attempt at a Solution


My group is divided. One of us thinks that the balloon's temperature should have decreased, as the pressure decreases (following the Ideal Gas Law up there). But another of us thinks that it should have increased, because the volume increased more than the pressure did.
 
Physics news on Phys.org
Welcome to PF.
What is the thermodynamic process you'd expect to be dominant when the balloon was popped?

What was the mean and standard deviation of the changes over many experiments?
Did you pop the balloon by inflating it until it burst or just pricking it with a pin?
 
Last edited:
We popped the balloon with a pin.

Our results show that the temperature of the air in the balloon either remained the same or increased by about 0.2-0.3 oC, but we're not sure if this is theoretically correct or simply due to human error. The mean over all our experiments should be around an increase of 0.06 oC or so.

If our results are correct, then I suppose the increase in volume took precedence over the decrease in pressure. But is that likely to happen?
 
You will get experimental variation due to lots of things - including variations in the composition of the balloons. It is just not the same each time. You'd expect so many random variations to produce a normal distribution in your results ... which is why mean and standard deviation are important. If "no change" is within 2sd of the mean change then your results are consistent with no change in temperature. (If there were any change, you failed to measure it.)

BTW: did you measure the pressure inside the balloon?

If our results are correct, then I suppose the increase in volume took precedence over the decrease in pressure. But is that likely to happen?
Well that is the question isn't it? So think of the different thermodynamic processes and ask which one you'd expect to be dominant. Should have done this before the experiment... it is seldom meaningful to confirm a theory after the fact.

Note: experimental results are always "correct". They are what you measured.
 
Do not forget the elastic wall of the balloon. While the gas extends through the hole into the external atmosphere and does work against the external pressure, the walls move inward, pressing the gas out. This is work done on the gas, warming it up, while the extension of the gas results in cooling down.

ehild
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Correct statement about a reservoir with an outlet pipe'
The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
Back
Top