How is Energy Exchanged in a Parallel Circuit?

AI Thread Summary
In a parallel circuit with a voltage source of 10√2 cos(2000t), a 10-ohm resistor, a 10mH inductor, and a 15μF capacitor, the energy exchanged between the source and the load is calculated to be 0.0962J, while the energy exchanged between the capacitor and inductor is 0.144J. There is a concern that the book's calculation of the equivalent impedance (Z_eq) may be incorrect, potentially leading to erroneous energy values. The correct Z_eq is found by adding the admittance of the components and inverting it, resulting in a value of 9.8 at an angle of 11.3 degrees. The energy calculations involve using the formulas for energy in inductors and capacitors, confirming that the load includes the resistor, inductor, and capacitor. The discussion emphasizes the importance of accurately determining Z_eq for correct energy exchange calculations.
Trooko
Messages
8
Reaction score
0

Homework Statement


All components arranged parallel,

voltage source =10sqrt(2)cos(2000t)
10 ohm resistor, 10mH inductor, 15 microF
How much energy is exchanged between the source and the load? (book answer: 0.0962J) Between the capacitor and the inductor? (0.144J)

But I think the book answer made a mistake in getting Z_eq which gave the wrong anwer. I think they left Z_eq invert and used it as Z_eq in calculation

Homework Equations


I_p = V_p / Z_eq
S =0.5 (V_P) (I_P*) -> giving a complex solution, where the real is P and I am is Q

Between source and load: W = Q/omega
Energy in inductor W = (0.5)( L )(I_P)^2
energy in capacitor W = (.5) (C) (V_p)^2

The Attempt at a Solution



Find the Z_eq by adding the admittance of the components, then invert it giving 9.8 with degree 11.3

Find I with the equation above 1.02 sqrt(2) degree -11.3

Find S giving Real(10) + Im(2) -> p=10 Q = 2

Energy between load and source: using omega = 2000 -> W = 2/1000 = 0.001

Energy between capacitor and inductor: I think it should be the energy of the inductor plus capacitor
 
Physics news on Phys.org
Is the load supposed to be the whole network, the resistor, or something else? Also, I think you are correct that it wants the energy of the inductor plus the capacitor.
 
Yes, The load consist of the resister, inductor and capacitor.
 
Thread 'Variable mass system : water sprayed into a moving container'

Thread 'Variable mass system : water sprayed into a moving container'

Starting with the mass considerations #m(t)# is mass of water #M_{c}# mass of container and #M(t)# mass of total system $$M(t) = M_{C} + m(t)$$ $$\Rightarrow \frac{dM(t)}{dt} = \frac{dm(t)}{dt}$$ $$P_i = Mv + u \, dm$$ $$P_f = (M + dm)(v + dv)$$ $$\Delta P = M \, dv + (v - u) \, dm$$ $$F = \frac{dP}{dt} = M \frac{dv}{dt} + (v - u) \frac{dm}{dt}$$ $$F = u \frac{dm}{dt} = \rho A u^2$$ from conservation of momentum , the cannon recoils with the same force which it applies. $$\quad \frac{dm}{dt}...
View full post »

Thread 'Struggle to understand the concept of the question (ice cube in water optics question)'

TL;DR Summary: I came across this question from a Sri Lankan A-level textbook. Question - An ice cube with a length of 10 cm is immersed in water at 0 °C. An observer observes the ice cube from the water, and it seems to be 7.75 cm long. If the refractive index of water is 4/3, find the height of the ice cube immersed in the water. I could not understand how the apparent height of the ice cube in the water depends on the height of the ice cube immersed in the water. Does anyone have an...
View full post »

Similar threads

Calculation of current in driven series RLC circuit
Replies
8
Views
2K
How to calculate quality factor for RLC circuit?
Replies
6
Views
1K
Solving for Imax and Energy in an LC Circuit: Homework Help
Replies
28
Views
4K
Energy and Voltage of Capacitor Circuits
Replies
5
Views
1K
Minimizing the Energy of Two Conductors Very Far Apart
Replies
23
Views
2K
How to find the energy of capacitance?
Replies
5
Views
2K
RC circuit - Rate o'energy dissipated = rate o'energy stored
Replies
8
Views
3K
Energy dissipated in the resistors in a 2 mesh RC circuit
Replies
1
Views
2K
Question about the energy stored in an RLC parallel resonant network
Replies
44
Views
5K
LC circuit -- Calculate the work done
Replies
5
Views
2K

Hot Threads

Recent Insights

Back
Top