On non linear resistor and how to calculate a fixed resistor.

  • Thread starter Thread starter physikamateur
  • Start date Start date
  • Tags Tags
    Linear Resistor
AI Thread Summary
The current through a non-linear resistor is defined by the equation I=0.05V^3, with a series connection to a fixed resistor and a 9V voltage source. To achieve a current of 0.40A, the voltage drop across the non-linear resistor is calculated to be 2V, resulting in a 7V drop across the fixed resistor. Using Ohm's law, the required resistance for the fixed resistor is determined to be 17.5 ohms. The calculations confirm that the approach to solving the problem is correct. The solution effectively integrates the non-linear characteristics of the resistor with standard circuit analysis.
physikamateur
Messages
12
Reaction score
0

Homework Statement



The current in amperes through a certain type of non-linear resistor is given by I=0.05V^3, where V is the potential difference in volts across the resistor. This resistor is connected in series to a fixed resistor and a constant voltage source of 9V is connected across the series combination. What value of resistance should the fixed resistor have so that a current of 0.40A flows ?

Homework Equations


V=IR and P=VI ?



The Attempt at a Solution


I first tried to calculate the total resistance which gives 22.5 ohms. But I do not know how to calculate the non-linear resistor as it does not obey ohm's law hence no proper formula can be used ? Please help.

Thank you.

 
Physics news on Phys.org
Suppose that, as stated, a current of 0.40A is flowing through the nonlinear resistor. What will be the voltage drop across it according to the given formula for it (you may have to rearrange the formula)?
 
By I=0.05V^3, when I=0.40A, V=2V. Hence voltage drop across the fixed resistor is 9-2=7V.
Therefore by V=IR, 7=0.4R,
Therefore R=17.5 ohms

Am I right ?
 
Looks good!
 
Thanks a lot !
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top