Roller Coaster and Centripetal Acceleration

AI Thread Summary
The discussion centers on calculating the height from which a roller coaster must descend to ensure the force exerted by the seat on a rider equals their weight at the top of a loop with an 8.00 m diameter. The key equations involve centripetal acceleration and conservation of energy principles. Initial calculations suggested a height of 10 m, but further analysis indicated the correct height is approximately 12 m. Participants clarified the relationship between forces acting on the rider and refined their calculations to arrive at a more accurate solution. The final consensus is that the height should be expressed in terms of the loop's radius, leading to the conclusion that the required height is 3 times the radius of the loop.
hrithikguy
Messages
3
Reaction score
0

Homework Statement



Part of a roller-coaster ride involves coasting down an incline and entering a loop 8.00 m in diameter. For safety considerations, the roller coaster speed at the top of the loop must be such that the force of the seat on a rider is equal in magnitude to the rider's weigt. From what height above the bottom of the loop must the roller coaster descend to satisfy this requirement?

Homework Equations



a_c = v^2/r
Conservation of Energy


The Attempt at a Solution


m* a_c = mg

m* v^2/r = mg
v^2/r = g
v^2 = rg

mgh = 1/2 mv^2 + mg * 8
9.8 * h = 1/2 * rg + 8 * 9.8

9.8 * h = 1/2 * 4 * 9.8 + 8 * 9.8
h = 2 + 8
h = 10

However, the answer is 12.

Please guide me to the solution.

Thanks!
 
Physics news on Phys.org
hrithikguy said:

The Attempt at a Solution


m* a_c = mg

m* v^2/r = mg
There act two forces on the rider, one is gravity (mg) and the other is the normal force N from the seat. The problem says that the seat must exert a force on the rider equal to mg. The resultant force is equal to the centripetal force.


ehild
 
So does this mean that n = -mg, so

m * a_c = 2mg ?

a_c = 2ga_c = 19.6

v^2/r = 19.6
v^2 = 19.6 * 4 = 78.4
v = 8.85

9.8 * h = 1/2 * 9.85^2 + 8 * 9.8

x = 12.95

Hmm.. this is closer, but still not correct.
 
Last edited:
You used v = 9.85 instead of 8.85. It is much better if you do not evaluate the equations, but express the height h in terms of R.

ehild
 
Ah thank you! I plugged in 8.85 now and it came out to 11.996, which is close enough.
Thanks!
 
I show the other way: mv^2/R=2mg
hmg=mg*2R+1/2 mv^2 -->

v^2=2gR,
hg=2gR+1/2v^2--->hg = 3gR ---> h=3R.

ehild
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Correct statement about a reservoir with an outlet pipe'
The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
Back
Top