Very Naïve Question About Electric Circuits

AI Thread Summary
The discussion centers around the behavior of electric circuits, specifically regarding a setup with two light bulbs connected to a button via a forked wire. It clarifies that if there is a break in the wire on one side, only the bulb on the unbroken side would illuminate, which aligns with the characteristics of a broken circuit rather than a short circuit. The conversation emphasizes that in a parallel wiring configuration, a break would prevent one bulb from lighting while the other still functions, whereas in a series configuration, a break would cause both bulbs to go out. The importance of checking the bulbs and understanding the circuit configuration is highlighted to diagnose the issue accurately. Overall, the thread provides insights into basic electrical principles and troubleshooting methods.
Howard Nye
Messages
12
Reaction score
0
Hi all,

I’m deeply ignorant about how electricity works. I just wanted to confirm that the following was possible:

I have a button on one end of a wire. The wire stays unified for about 3 feet, then forks into a right section and a left section, each of which is about 3 feet long, and each of which is connected to a different light-bulb. Pressing the button closes a circuit that causes current to travel to both light-bulbs and illuminate them. One day, there is a short in the right fork of the wire. So now when I push the button the light-bulb connected to the left fork of the wire illuminates but the light-bulb connected to the right fork of the wire does not illuminate.

Is that what would happen with the short in the right hand fork of the wire? I thought it was, but in my ignorance I wasn’t sure if this could screw up the circuit on the left hand of the fork, and I wasn’t sure if this sort of Y-shaped circuit was even possible.

Thanks so much,
Howard
 
Physics news on Phys.org
What you describe sounds more like an open circuit/broken wire than a short circuit.

Normally light bulbs are wired in parallel and a short circuit of the type you describe wouldn't cause one to work and the other not. Instead it would most likely stop both bulbs working and blow a fuse in the power supply.

If the bulbs are wired in series (eg two 6V bulbs connected to a 12V battery) then a short might cause the symptoms you describe.

Hard to say really as it depends not only on the electrical circuit but the physical layout. If this were house wiring the short might not even be within the circuit but between this and another circuit.
 
Hi CWatters,

Thank you very much! Yes, I think I meant a broken wire / open circuit, and I think I had in mind them being wired in series, e.g. by both being connected to the same battery.

So if it's just a broken wire - i.e. if there was a break in the right fork of the wire but not the left - would it matter whether the bulbs were wired in series or parallel? Would in both cases the switch turn on both bulbs before the break, but only the bulb connected to the left fork of the wire after the break?

Thanks again!
Howard
 
Howard Nye said:
Hi CWatters,

Thank you very much! Yes, I think I meant a broken wire / open circuit, and I think I had in mind them being wired in series, e.g. by both being connected to the same battery.

So if it's just a broken wire - i.e. if there was a break in the right fork of the wire but not the left - would it matter whether the bulbs were wired in series or parallel?

Thinking about it some more, the symptoms you describe are most likely consistent with

a) Parallel connection and a break

and less likely to be (with reason)..

b) Series connection and a short (the good bulb would be brighter than normal or fail due to over voltage).
c) Series connection and a break (both lamps would go out)
d) Parallel connection and a short (fuse would blow)

Whichever the fault is most likely to be in the leg that's not lit. Check the bulb first :-)
 
electricity won't travel through a short/ground or open circuit to find the path of least resistance, as (air is highly resistant to electricity)

it illuminates a bulb like water pressure on a water wheel/mill (to perform power) but/through a wire
 
Last edited:
Thread 'Griffith, Electrodynamics, 4th Edition, Example 4.8. (Second part)'
I am reading the Griffith, Electrodynamics book, 4th edition, Example 4.8. I want to understand some issues more correctly. It's a little bit difficult to understand now. > Example 4.8. Suppose the entire region below the plane ##z=0## in Fig. 4.28 is filled with uniform linear dielectric material of susceptibility ##\chi_e##. Calculate the force on a point charge ##q## situated a distance ##d## above the origin. In the page 196, in the first paragraph, the author argues as follows ...
Thread 'Inducing EMF Through a Coil: Understanding Flux'
Thank you for reading my post. I can understand why a change in magnetic flux through a conducting surface would induce an emf, but how does this work when inducing an emf through a coil? How does the flux through the empty space between the wires have an effect on the electrons in the wire itself? In the image below is a coil with a magnetic field going through the space between the wires but not necessarily through the wires themselves. Thank you.
Back
Top