Charging an iphone with macbook charger

AI Thread Summary
Charging an iPhone with a 61W MacBook charger via USB-C is safe, as the phone will only draw the power it needs. Any USB-C charger can be used to charge the iPhone, not just Apple products, due to the phone's internal circuitry managing power requirements. The discussion highlights that the transition to USB-C was influenced by EU regulations aimed at standardizing chargers for environmental reasons. Previous charging issues were often due to debris in the iPhone's Lightning connector, while USB-C cables have their contacts in the connector, reducing potential damage. Despite initial expectations, Apple has opted not to adopt USB-C for future iPhone models.
Lobotomy
Messages
55
Reaction score
0
So I can charge my iphone, with the 61W macbook charger using the USB-C interface. I think the battery won't draw more effect than it needs/is dimensioned for, so this works fine. Can i use any charger with an USB-C interface to charge my iphone?
or does it only work with apple products?

Or more generally, is the circuitry required for this, inside the phone, or inside the adapter? would it be possible to design a product, that can be charged with any type of USB-C adapter for small appliances/computers/phones etc, regardless of the adapter effect etc (within reasonable limits)?
 
Engineering news on Phys.org
I think the reason Apple moved to the USB-C was due to pressure from EU regarding consolidation of chargers down to a common green standard.

https://www.theverge.com/21522980/a...ning-environment-charger-box-electronic-waste

Also the failure mode on the previous charging connection was in the iPhone connector itself and not in the cable.

remember cleaning out some debris that got into my iphone socket and may have caused some damage to the springy contacts which caused the cable to not sit well and the phone to not charge.

With a USB-C cable the springy contacts are in the cable connector not in the iPhone.

However, apparently Apple has recently decided (May 2020) to not go the USB-C route at all:

https://www.forbes.com/sites/gordon...ss-charging-upgrade-iphone-11-pro-max-upgrade
 
jedishrfu said:
I think the reason Apple moved to the USB-C was due to pressure from EU regarding consolidation of chargers down to a common green standard.

https://www.theverge.com/21522980/a...ning-environment-charger-box-electronic-waste

Also the failure mode on the previous charging connection was in the iPhone connector itself and not in the cable.

remember cleaning out some debris that got into my iphone socket and may have caused some damage to the springy contacts which caused the cable to not sit well and the phone to not charge.

With a USB-C cable the springy contacts are in the cable connector not in the iPhone.

However, apparently Apple has recently decided (May 2020) to not go the USB-C route at all:

https://www.forbes.com/sites/gordon...ss-charging-upgrade-iphone-11-pro-max-upgrade

ok, that's interesting information but it doesn't really answer my questions...
 
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...

Similar threads

Back
Top