Projectile motion ball question

AI Thread Summary
A ball rolling off a shelf of height h lands a distance x1 from the edge, while a second ball from height 2h lands a distance x2 away. The horizontal motion remains constant, and the time of flight for each ball is crucial in determining the distances. The time of flight can be related to the heights, leading to the conclusion that the ratio of the distances x1/x2 is equivalent to the square root of the ratio of the heights. Ultimately, the higher ball will land farther from the edge by a factor of √2. Understanding these relationships clarifies the projectile motion involved.
Kristin_Z
Messages
9
Reaction score
0
A ball moving with speed v rolls off a shelf of height h and strikes the floor below a distance x1 from the edge. A second ball moving with the same speed rolls of a self of height 2h and strikes the floor a distance x2 away from the edge. Determine the ratio of distances x1/x2.
\Deltax=Vxt
\Deltay=vt +1/2st2
The horizontal motion of the ball is constant and, therefore, not affected by the height from which it rolls. But I cannot figure out how to formulate the ratio of the distances. I know that time relates the two equations of motion and that because the ball is rolling it has no initial vertical velocity and that since it is free fall the acceleration would be the same for the two equations. I just can't seem to get the equation to make sense when I write it out. Any help would be greatly appreciated. Thanks!
 
Physics news on Phys.org
Kristin_Z said:
A ball moving with speed v rolls off a shelf of height h and strikes the floor below a distance x1 from the edge. A second ball moving with the same speed rolls of a self of height 2h and strikes the floor a distance x2 away from the edge. Determine the ratio of distances x1/x2. The horizontal motion of the ball is constant and, therefore, not affected by the height from which it rolls. But I cannot figure out how to formulate the ratio of the distances. I know that time relates the two equations of motion and that because the ball is rolling it has no initial vertical velocity and that since it is free fall the acceleration would be the same for the two equations. I just can't seem to get the equation to make sense when I write it out. Any help would be greatly appreciated. Thanks!

Well I can see you are almost grasping it.

The horizontal motion is constant, that's true, but what affects the distance at which it lands?

d1 = V*t1
d2 = V*t2

So ... the ratio of the distances then will be in the same ratio as the ratio of the times won't it?

And now is there some way to relate the ratio of the times using the heights?
 
I think I have it now.

2y = 1/2 at12 divided by y = 1/2 at22

gives me 2= t12t22

so t1t2 =square root of 1/2.

Thanks for your help, still not entirely sure I understand what I did. I guess that's what practice is for.
 
Kristin_Z said:
I think I have it now.

so t1t2 =square root of 1/2.
.

Check this step.
 
Kristin_Z said:
I think I have it now.

2y = 1/2 at12 divided by y = 1/2 at22

gives me 2= t12t22

so t1t2 =square root of 1/2.

Thanks for your help, still not entirely sure I understand what I did. I guess that's what practice is for.

I think you really meant
2= t12/t22

Which yields the ratio

t1/t2 = √2

But I would note the original statement has y2 being 2*y1, so I think you have your subscripts reversed.

The higher ball would fall farther from the base by a factor of √2 is the sense of you should be grasping.
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Struggling to make relation between elastic force and height'
Hello guys this is what I tried so far. I used the UTS to calculate the force it needs when the rope tears. My idea was to make a relationship/ function that would give me the force depending on height. Yeah i couldnt find a way to solve it. I also thought about how I could use hooks law (how it was given to me in my script) with the thought of instead of having two part of a rope id have one singular rope from the middle to the top where I could find the difference in height. But the...
Back
Top