Transistor output resistance and thermal voltage

AI Thread Summary
The discussion focuses on the thermal voltage (VT) of pn junctions and small signal output resistance (ro) in BJTs. VT is a constant determined by temperature and is applicable to all pn junctions, though device characteristics can vary due to factors like doping and material. The output resistance ro is calculated using the equation ro = (VA + VCE) / IC, but practical determination of ro can be challenging as it is not commonly listed in datasheets. To find the Early voltage (VA), one can analyze collector curves from datasheets, extending the saturation region to determine where they intersect at Ic = 0. In many circuits, the external collector resistor is much lower than ro, making it less critical in small signal analysis.
tindel
Messages
12
Reaction score
0
A couple questions:

I'm in the process of making some small amplifiers and using bjt's in the small signal realm. I have used bjt's as switches for quite a while, so I am quite familiar with their basic operation. I was reviewing small signal analysis trying to refresh my memory about how to do the analysis when I came across a couple variables that I'm not sure how to incorporate them into my analysis in a practical sense.

First, thermal voltage of a pn (diode) junction - VT - which my book describes as a 'constant', which is a function of temperature. VT is defined as

VT= k*T / q

where
k is Boltzmann's constant = 1.38 x 10^-23 joules/kelvin,
T= temperature kelvin,
q= magnitude of electronic charge = 1.6 x 10^-19 coulomb

Is this true for all pn junctions - or does this change with doping, diode types, etc?


Second - small signal output resistance, ro - my book does an awful job explaining how to arrive at this value, practically speaking. They give the following equation for the output resistance ro = (VA + VCE) / IC. I have never seen ro or VA in a datasheet. I'm not sure what VA even is. I do understand that ro is a function of collector current due to vce, so I understand why it's used, I just don't understand when I have a circuit I'm analyzing, how to come up with a value of ro!

True to form - my old electronics book tells me how to do all the calculations, but doesn't explain how to arrive at the value in a practical sense. A quick google search also turned up nothing.
 
Engineering news on Phys.org
The term kT/q is not really a parameter of the diode (or transistor) itself, but is actually just the thermal energy of the carriers in the semiconductor, expressed in electron volts. The electrical properties of diodes and transistors do depend upon this quantity, but also on many other parameters of the device. So in summary, yes this quantity is the same for all semiconductors at a given temperature, but the characteristics of those different devices can still be different due to other factors like physical dimensions, doping levels and the intrinsic semiconductor material itself.
 
Last edited:
tindel said:
A couple questions:

I'm in the process of making some small amplifiers and using bjt's in the small signal realm. I have used bjt's as switches for quite a while, so I am quite familiar with their basic operation. I was reviewing small signal analysis trying to refresh my memory about how to do the analysis when I came across a couple variables that I'm not sure how to incorporate them into my analysis in a practical sense.

First, thermal voltage of a pn (diode) junction - VT - which my book describes as a 'constant', which is a function of temperature. VT is defined as

VT= k*T / q

where
k is Boltzmann's constant = 1.38 x 10^-23 joules/kelvin,
T= temperature kelvin,
q= magnitude of electronic charge = 1.6 x 10^-19 coulomb

Is this true for all pn junctions - or does this change with doping, diode types, etc?

I cannot answer about the doping, but yes V_T=\frac {kT}{q}\; holds for all transistor and diodes.

Second - small signal output resistance, ro - my book does an awful job explaining how to arrive at this value, practically speaking. They give the following equation for the output resistance ro = (VA + VCE) / IC. I have never seen ro or VA in a datasheet. I'm not sure what VA even is. I do understand that ro is a function of collector current due to vce, so I understand why it's used, I just don't understand when I have a circuit I'm analyzing, how to come up with a value of ro!

True to form - my old electronics book tells me how to do all the calculations, but doesn't explain how to arrive at the value in a practical sense. A quick google search also turned up nothing.

A lot of transistor data sheets provide collector curves for different Ib. To find the early voltage, extend the straight portion of the curve ( the saturation region) to the left side where Vce going to negative. Keep extending all and they all will meed at Ic = 0. Read off the Vce and that's the early voltage.

r_0\; is defined as change of collector current to change of Vce. That is the slope of the collector curve when the transistor is in saturation region ( the straight part of the curve). As you can see, the slope is different for every Ib. Therefore r_0\; is collector current dependent. Normally r_0\; is not that important as you have collector resistor R_L\; which is usually much lower. The total load resistance is r_0\; parallel with R_L\; which essentially just R_L\; when it is a lot lower than the output resistance. It is important when you use it as a current source where you need very high impedance at the output. In IC, most circuit use active load, then it is more important as it affect the gain of the transistor if this is the load on the collector.
 
Last edited:
tindel Second - small signal output resistance said:
o[/SUB] - my book does an awful job explaining how to arrive at this value, practically speaking. They give the following equation for the output resistance ro = (VA + VCE) / IC. I have never seen ro or VA in a datasheet. I'm not sure what VA even is. I do understand that ro is a function of collector current due to vce, so I understand why it's used, I just don't understand when I have a circuit I'm analyzing, how to come up with a value of ro!
Apart from using the "Early voltage" (as explained by yungman above) many datasheets will specify the common emitter r_o indirectly via the parameter h_{oe}. This parameter is in fact the reciprocal of r_o.

Remember that in an actual circuit that the (external) collector resistor will be in parallel with r_o in the small signal model. Very often this external R_C is much lower than r_o and so dominates the parallel combination (meaning that you can often ignore r_o without introducing too much error in the analysis).
 
Thanks uart and yungman - The data you gave on both the early and thermal voltages is very useful. I understand that ro is very large, and with small output resistances, relative to ro I understand that it is not much of a concern unless you have large output resistances.
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
Thread 'Beauty of old electrical and measuring things, etc.'
Even as a kid, I saw beauty in old devices. That made me want to understand how they worked. I had lots of old things that I keep and now reviving. Old things need to work to see the beauty. Here's what I've done so far. Two views of the gadgets shelves and my small work space: Here's a close up look at the meters, gauges and other measuring things: This is what I think of as surface-mount electrical components and wiring. The components are very old and shows how...
Back
Top