Where do I get started with analog/digital circuit design?

AI Thread Summary
To get started with analog and digital circuit design, it's essential to build a strong foundation in electrical physics, focusing on voltage and current. "The Art of Electronics" by Horowitz and Hill is highly recommended as a comprehensive resource. Practical experience is crucial, so engaging in hands-on projects with kits and breadboards will enhance understanding. Familiarity with basic components like resistors and capacitors is also important. Combining theoretical knowledge with practical application will lead to a deeper grasp of circuit design.
tkahn6
Messages
13
Reaction score
1
How do I even get started with analog/digital circuit design?

Can you recommend any books or lectures I can read or watch?

How did you get started?

Thanks!
 
Engineering news on Phys.org
tkahn6 said:
How do I even get started with analog/digital circuit design?

Can you recommend any books or lectures I can read or watch?

How did you get started?

Thanks!

Welcome to the PF. Where are you in school? What kits/projects have you built so far?

I'm a broken record when it comes to recommending a cover-to-cover read of "The Art of Electronics" by Horowitz and Hill. Do you have a technical library nearby where you can check out a copy?
 
berkeman said:
Welcome to the PF. Where are you in school? What kits/projects have you built so far?

I'm a broken record when it comes to recommending a cover-to-cover read of "The Art of Electronics" by Horowitz and Hill. Do you have a technical library nearby where you can check out a copy?

Thanks!
I'm a Junior in high school. As for my experience, I've stuck with teaching myself computer science for the past few years. Thus, I've built no models nor messed with any kits. However, I am quite familiar with C and have a working knowledge of pointer arithmetic/manipulation (if that helps).

I'm currently on spring break and with a physics book I'm teaching myself electrical physics.

Thanks again for your reply! I'll try and pickup a copy of the book you recommended tomorrow.
 
tkahn6 said:
Thanks!
I'm a Junior in high school. As for my experience, I've stuck with teaching myself computer science for the past few years. Thus, I've built no models nor messed with any kits. However, I am quite familiar with C and have a working knowledge of pointer arithmetic/manipulation (if that helps).

I'm currently on spring break and with a physics book I'm teaching myself electrical physics.

Thanks again for your reply! I'll try and pickup a copy of the book you recommended tomorrow.

Definitely. Pick up a used copy of H&H, and build a couple kits. See the other posts on this theme in the EE forum, and then kick some ____.
 
There is tons of info on introductory electronics out there. A quick way is to google and wiki various topics in.

Besides the theory, there is nothing like building and testing circuits. You can pick up a breadboard, some wiring, a couple of resistors and capacitors in radio shack, as well as an op-amp. Put those together, and see how well your circuit agrees with theory.
 
tkahn6 said:
I'm currently on spring break and with a physics book I'm teaching myself electrical physics.
It starts with the basics. The two fundamental building blocks are voltage and current. Use the physics book to get a handle on those, and basic resistor circuits. After that an actual electronics book is the way to go, and Horowitz and Hill is widely recognized as the best there is.

Good luck!
 
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Thread 'Electromagnet magnetic field issue'
Hi Guys We are a bunch a mechanical engineers trying to build a simple electromagnet. Our design is based on a very similar magnet. However, our version is about 10 times less magnetic and we are wondering why. Our coil has exactly same length, same number of layers and turns. What is possibly wrong? PIN and bracket are made of iron and are in electrical contact, exactly like the reference design. Any help will be appreciated. Thanks. edit: even same wire diameter and coil was wounded by a...
Back
Top