Vessel Definition and 217 Threads

Is there a specific location (say top, bottom etc.) that a safety relieving valve is put on a pressure vessel? Say there's a tall refining separation column (operating above atmospheric pressure), where would logic (or codes) indicate that a pressure relief valve ought to be ideally placed...

Design a railway cistern for 120,000 kg of Liquid. It has to be a cylindrical shell on two supports. The cistern is 18 m long 3 m in diameter (inner). It is made of steel with the yield strength of SY= 240MPa. Safety factor of FY= 1.9; Total corrosion allowance, c= 3.0 mm; Welded joint...

Note: this is not a homework question; this is strictly conceptual in understanding the equations at work in this scenario. The tank is vacuum-insulated, the liquid is saturated, and the vents have just been opened in order to vent down the ullage pressure. My question is simply how do you...

Hi, I was wondering if anyone knew where I could buy a pressure vessel that meets the following specifications: min. pressure: 2,000 psi max temp.: at least 800°C volume: around 80-100 mL I've been searching for around month now with little success... I could really use some help...

Homework Statement A rigid vessel of volume 2.5 m3 contains steam at a pressure of 6 bar and a dryness fraction of 0.75. If the contents of the vessel are heated, determine: i) the pressure at which the steam becomes dry saturated, ii) the temperature of the steam when the pressure reaches...

Assume we have a vessel capable of withstanding infinite pressure. What happens to the pressure inside the vessel when that vessel is filled completely with water, with no air space at the top, and is then heated? Do the equations for vapor pressure still apply if there's no space for a vapor...

Suppoese there is a empty vessel connected to a pipeline having a continuous supply of gas at pressure P. Gas will continue to move in vessel till pressure in it become P. How to calculate time required to fill the vessel completely. Plz help.

one mole of liquid water (100 deg C, vapor pressure = 1 atm) in a container is introduced into an evacuated vessel maintained at 100 deg C and allowed to evaporated. The volume of the vessel is such that the final pressure of the gaseous water is 0.1 atm. Given the (normal) latent heat of 9,730...

I have a question about a Fiberglass Hemisphere that is 16" in diameter and 8 " in height. It is being used as a vessel under the water so it has a closed top. I wanted to know how to figure out how much stress from water pressure it will handle before it fails. thanks!

I have no intention of designing, building or experimenting with this, so no worries about safety. I'm just curious and did a Google search for Physics Forums and this was the first to come up. I was wondering, when pressure decreases so does temperature, right? So, were we to have a pop...

I'm working on the design for a dry-hull model submarine. My plan is to cast the hull shape that I want out of aluminum because this type of casting is cheap, easy to make, and because aluminum has a good strength to weight ratio. I want the hull to be able to withstand an external pressure of...

Homework Statement One kg of air is heated in a closed rigid vessel such its temperature changes from 27 C to 427 C . Find the heat transfered and change in internal energy . Assume : - R= 0.287 KJ/kg k Cv = 0786 KJ/Kg k Homework Equations Q = mXCX(T2 - T1 ) The Attempt at a...

Hi, I am working on a project that requires me to pressurize water in a small pressure vessel up to a pressure of 1500 psi. I am searching for a pump to do this. Do you guys think a pressure washer pump such as this one...

I am needing to calculate the fill time of a pressure vessel. I know the following parameters regarding the vessel: Volume, Temperature, Properties of the fluid media, inlet pipe diameter, flow rate of the inlet, pressure of the inlet. I tried calculating the mass flow rate of the inlet...

Hey guys I'm new here. I need to find a generic pressure vessel that can take in a gas at up to 6MPa and then have a quick release system that would allow me to very quickly depressurize/open it and remove the contents within ~10 seconds or less. Right now we use bolts to hold down the lid...

Hey guys, I am trying to conceptualize as to why shear stress in a vessel is highest at the wall of the vessel and why it is at a minimum at the center. First let me see if I actually understand shear stress - In a vessel with blood flow, it is the force required to overcome the...

A closed vessel full of water is rotating with constant angular velocity \Omega about a horizontal axis. Show that the surfaces of equal pressure are circular cylinders whose common axis is at a height g/{\Omega}^2 above the axis of rotation. Any ideas? I do not know how to start.

When temperature of water in earthen pot is less than temperature outside, will earthen vessel help in maintaining the temperature of water inside constant (or) will it help by decreasing the temperature inside?

Homework Statement Problem: find the thickness of a Pressure Vessel. Given: Operating Pressure, Operating Temperature, Material type and Grade, and OUTSIDE Diameter/Radius Homework Equations q1. how to calculate Design Pressure/Temp. from Operating Pressure/Temp.? q2. how to calculate...

Today i was heating a bowl of soup..the intensity of the flame of the gas stove was quite high.. i observed that the bowl got burnt and when it cooled down a bit, i observed a band of colours..blue was the most prominent..i noticed the presence of violet, yellow and orange too.. I wish to know...

Question: How can I estimate the amount of air that leakes into a vacuum vessel. I know the pressure outside the vessel (1020 mBar), the pressure achieved in the vessel (10 mBar), the pumping speed of the vacuum pump (400 cubic metres per hour) and the duration of the leaking (6 hours). Volume...

Hi guys. I am trying to figure out how thick should be an aluminium pressurized vessel with a internal pressure of 0.125 pa or 1/8 bar. The shape of the box is a cylinder 130cm base x 170cm height. The maximum pressure difference is 0.125 bar inside -> 0 bar outside. I know that i need to know...

Homework Statement My question has to do with heating water to a superheated state inside a constant volume vessel. Given: A pressure vessel with a total volume of 36.77ft^3, is filled with 5 gal of water and heated from room temp. to a final temp. of 1100°F. Obvisouly the initial pressure...

My question has to do with heating water to a superheated state inside a constant volume vessel. Given: A pressure vessel with a total volume of 36.77ft^3, is filled with 5 gal of water and heated from room temp. to a final temp. of 1100°F. Obvisouly the initial pressure is atmospheric and...

Hi, It is well known that a sphere has the lowest surface to volume ratio. However, a related question is: What is the shape that gives the lowest surface to volume ratio if you do not include the "top" in the surface. That is, what is the maximal volume of an uncovered vessel of a fixed...

A vessel is divided into two parts of equal volume by a partition in which there is a very small hole. Initially, each part contains gas at 300K and a low pressure, p. One part of the vessel is now heated to 600K while the other is maintained at 300K. If a steady state is established when the...

Hi, I'm looking for a method to calculate how much time it will take to pressurize a vessel from 1 atm to 60 psig after a flow control valve is opened. The method I was considering using is: I was thinking about using PV=nRT and (P1*V1)/T1=(P2*V2)/T2 to determine the # of moles in the...

Description is in the image as well as the question. I was wondering for a) do i need to take into account the compressive forces that is acting on the vessel? Cheers

Hi, Does anyone has experience using accelerometer on a ship/vessel to detect whether the vessel is moving or stationary? The difficult part is that I took some samples at 6Hz and found that all X/Y/Z axes have accelerations going positive and negative. The pattern is exactly the same...

Homework Statement Homework Equations σ=pr/t (hoop) σ=pr/2t (longitudinal) τ=VQ/It The Attempt at a Solution I have longitudinal stress and hoop stress. I'm trying to find shear stress, which should come only as a result of the 40kN from the collar correct? I'm confused...

I need help understanding certain aspects of this problem... Problem statement Write an integral expressing the amoutn of force on one trapezoidal side of this water vessel when the height of the water is H meters. The density of water is 1000 kg/m3, and the force of gravity is 9.8 N/kg...

Hello, This is my first post, so I believe, that you understand and help for me. So I have a task to design vacuum vessel, precisely, my task names "Training stand to measure the height of the flight fuel pump". Height will be simulated by vacuum in fuel tank, which will create a vacuum pump...

Hello everyone! Anybody deals with nuclear waste? I got a question about the maintenance vessel Lepse, which is fully loaded with radwaste. Here is a link: http://www.bellona.org/english_import_area/about_bellona/33320 There are many cases (or tubes) containing one spent fuel assembly...

Hi everyone, I have to determine the size of safety valve for an air pressure vessel. I found in ASME and BS 5500 a procedure to calculate the size of safety valve, which relates the mass flow capacity to the: pressure, temprature, discharge area, s.v coefficient, and air parameters. This can...

I don't know if its daylight savings or what, but I just can't seem to wrap my head around this analysis. There is a polycarbonate hemispherical head with 8 psi in a near vacuum environment (2.8 torr) Im trying to figure out what the minimum thickness is for the head. The shell is super...

The pattern could be at an arterial, arteriole or capillary level. There are plenty of examples of branched patterns in organisms. [SIZE="1"](C) Baccar et al, Difficulté du diagnostic étiologique d’un poumon clair unilatéral, La tunisie Medicale - 2011 ; Vol 89 ( n°06 ) : 578-579 But...

Homework Statement derive the equilibrium state of the stress at a point in a circular pressurized vessel, membrane equation, in terms of σ_a and σ_b and internal pressure b. Figure is picture of a thin walled pressurized elliptical vessel (like a sphere vessel except with horizontal...

A vessel filled with two liquid how to determine boyant force? A vessel contains oil of density(800kgm-3) over mercury (density 13600kgm-3) A homogeneous Sphere is floats with half of its volume immersed in mercury and other half in oil. What is density of the material of the sphere? How...

1 g mole of oxygen at 27 degree Celsius and 1 atmospheric pressure is enclosed in a vessel. The vessel is thermally insulated. This vessel is moving with speed of v0. Suddenly it is stopped. what will change in temperature of the gas. How i did it. first of all i find the root mean speed of the...

helping a relative with their final studying but its been a few years since I've taken intro phys Suppose a blood vessel is horizontal and it has wide and narrow cross sections as shown in Fig 1. In the real life the edges are not sharp and we assume their effects are negligible. Suppose the...

Dose anybody can give me link for ASME codes for boiler & vessel pressure. Thanks

Hi, I cannot find any equation to help determine the resultant pressure from heating water in a sealed metal container, all I find is PV-nRt which is only gas - We are heating doing this in part to pretreat biomass. sealed tube: vol =170cc containing 80ml.s water: tube heated to 180C. I...

Homework Statement It is known that water in a capillary will rise to a certain height, as shown in the figure. Comparing the points P and Q, which point exhibit larger pressure? a. P b. Q c. The pressure of P and Q are the same Homework Equations F_upward=2*pi*R*T*cos⁡θ W=pi*R^2*...

Hi all, I am facing the problem with shore power supply for the vessel. At our ship yard, sometimes we need to arrange temporary electric supply for the vessel meanwhile their generators are overhauled. For 440 V 60 Hz i am using portable generator supply and for 415 V 50 Hz supply i am...

Homework Statement A vessel whose walls are thermally insulated contains 2.40kg of water and 0.450kg of ice, all at a temperature of 0.0 C. The outlet of a tube leading from a boiler in which water is boiling at atmospheric pressure is inserted into the water. How many grams of steam must...

This is a real world problem. We have a vessel sunk in about 50' of water and need to raise it. We have devised a way to pump the water out and pump air into replace the water. It is important that we keep the differential pressure very close to Zero and running a "snorkle" tube is not an...

I would like to make a pressure vessel with a pressure of about 9 bars/130.5 psi, that contains about 250 grams of water at about 175 degrees Celsius. My question is how big should the pressure vessel be.

Homework Statement Hi, this is my first time posting so I hope you can see the attachment. Homework Equations Hoop stress = pr/t Longitudinal stress = pr/2t The Attempt at a Solution I am stuck on part a), afterwards I think I should be fine. I am guessing you can "add" axial...

Hello, I have been designing a pressure vessel for the last week. I have based all my maximum allowable stresses on ASME code but can't figure out how to include drilled holes. I plan to be using a pipe welded to a cap at one end and attached to a blind flange with holes drilled in it at the...

Hey everyone, hoping someone can point me in the right direction with a deflection question. A pressure vessel I'm working on needs to be pressure tested before it can be shipped out to the customer, so I'm having a large plate cut to match the flange. The opening is about 1500mm in diameter...