Catapult/Projectile Launcher Project - In Depth, Fairly Complicated - I'm stuck.

AI Thread Summary
The project involves creating a projectile launcher that must accurately fire a golf ball through a 0.5x0.5 meter window located at two different distances (2 meters and 4 meters) while landing on a target 8 meters away. The launcher is constrained to a 1x1x1 meter size with no weight restrictions. The creator has calculated an initial launch angle of 17.51 degrees and a speed of 9.08 m/s but struggles with determining the spring constant and other variables due to the elastic material used. Despite various attempts and calculations related to projectile motion, the creator is stuck and has not received adequate support from their teacher. The project deadline is imminent, adding urgency to finding a solution.
Zealot644
Messages
3
Reaction score
0

Homework Statement


I am required to make a projectile launcher of some form that will fire a golf ball a certain distance, a certain height through a window, and to have it land accurately on a target.

-The device can only be 1x1x1 meter - no weight restrictions.
-There will be two launches with 3 attempts each.
-Launch 1 will have a 0.5x0.5 meter window located 2 meters away, and will be 2 meters high.
-Launch 2 will have the same window, and the same height, but will be 4 meters away instead.
-For each launch, the ball must pass through the window and then land at the target which is located 8 meters away.

Here is a picture which helps describe a bit better: (to hell with 'not being able to include links'), type in i.imgur followed by .com and then /PKWAe.png

I have been unable to solve this problem so far because it involves something I am building in real life. I will describe what I have below.

I have done various calculations but they involve 'perfect' materials and such, which is impossible for me. I have determined, to my capability, that the ball must be launched at an angle of 17.51 degrees and a speed of 9.08m/s. But I had to make up a spring constant as I don't know what mine is for the elastic material I am using.

Homework Equations



Stuff to do with projectile motion. I've tried a few equations.

t=d/v
2gy=0-Viy^2 height I must reach above launch location, 1.25m
ax^2+bx+c=0 to get the time it will be in the air, 0.51s
v=d/t to determine the X velocity of 15.68
Tanθ=O/A to get launch angle
Sinθ=O/H to get diagonal launch speed
F=kx^2 to get my elastic constant K which ended up being 0.023
F=ma to try and get F of 5.74N, to allow for rearranging of K.
2as=vf^2 to get the acceleration per second of 124.92m/s

The Attempt at a Solution



I have made a projectile launcher : type in i.imgur followed by .com and then /RqRlp.png

It consists of two vertical boards on a platform. They are hinged - allowing for adjustment of holes at various heights by moving the firing platform.

The platform itself is a flat board with two pieces I cut at 45 degree angles for the ball to rest in. The ball will find its own center that way. The board itself can attach to different heights where holes have been drilled, and can pivot almost 90 degrees upwards.

The ball is fired through the use of an elastic material which I was provided, it seems to be the inflatable lining from inside a bicycle tire, and once cut into thin strips should be elastic enough.

I used all the equations I have listed to try and figure this out, but I am entirely stuck because...

I cannot find out K for sure, V for sure, A for sure - all of which prevents me from the correct angle and height.

I cannot figure out how to calculate firing from the elevated height. I decided that from 1m, in order to go above 2m and through the window, the ball must be fired to an elevation of 1.25m higher than the launch point, thus up to 2.25 meters.

Once the ball reaches 8m after passing through the windows, that is the 8m which is still located 1m above the ground, and it would keep moving horizontally past 8m until finally hitting the ground 1m below.Honest to god, I'm awful at physics and my passing is relying heavily on this project being successful. I have until Tuesday to get it done, and have been trying to work on it here and there for two weeks but I have reached a road block. I cannot get the correct variables to fire it properly, and the teacher has been of zero help so far. I hope my post makes some semblance of sense and perhaps can help with others helping me out - because I am entirely stumped on what to do.

If you need clarification on anything, just ask.
 
Physics news on Phys.org
All these views and no reply :(?
 
Bump...
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...

Similar threads

Back
Top