How does the phase of a wave change over time at a given position?

AI Thread Summary
A 403 Hz wave traveling at 200 m/s requires calculations for phase differences over time and distance. The first part of the problem was solved, determining that points differing by 1.9 rad are spaced 0.15 m apart. The wave's periodic nature is emphasized, with phase changes occurring over time intervals related to frequency. The time period T is calculated as the inverse of frequency, and the phase difference over a 4.8 ms interval is sought. The discussion highlights the importance of understanding wave properties and periodicity in solving these types of problems.
yuihatano
Messages
2
Reaction score
0

Homework Statement


A 403 Hz wave travels at 200 m/s along a wire.

a)At a given time, the distance between points that differ in phase by 1.9 rad is ___ m.
b)At a given position, the change in phase during an interval of 4.8 ms is ___ rad.

Homework Equations


V=w/k
w=2pif

The Attempt at a Solution



I 've already solved for a), it was pretty straight forward. Now, I'm stuck on b)

w=2pif
=2pi*403
=806pi

v=w/k
k=w/v
=806pi/200
=4.03pi

delta phi = x/k
= 1.9/4.03pi
=0.15m
this was for number 1... now I'm stuck on b)
pls help...
 
Last edited:
Physics news on Phys.org
The wave is periodic both in time and position. The displacement in a sine wave is

u=A*sin(2p(t/T-x/lambda)) or in other form u=A*sin(wt-kx),

with w=2pi/T and k=2pi/lambda.

The term 2pi(t/T-x/lambda)=wt-kx is the phase of the wave.

T is the time period and the period in space is lambda. At a given time t, two points which are lambda distance apart differ by 2pi in phase. At a certain position x, the phase changes by pi during T time interval.

You know the frequency f, so you know the time period T=1/f. The elapsed time is given, dt=4.8*10-3 s, what is the phase difference between t and t+dt?

ehild
 
ehild said:
The wave is periodic both in time and position. The displacement in a sine wave is

u=A*sin(2p(t/T-x/lambda)) or in other form u=A*sin(wt-kx),

with w=2pi/T and k=2pi/lambda.

The term 2pi(t/T-x/lambda)=wt-kx is the phase of the wave.

T is the time period and the period in space is lambda. At a given time t, two points which are lambda distance apart differ by 2pi in phase. At a certain position x, the phase changes by pi during T time interval.

You know the frequency f, so you know the time period T=1/f. The elapsed time is given, dt=4.8*10-3 s, what is the phase difference between t and t+dt?

ehild

Thank you!
 
Thread 'Minimum mass of a block'
Here we know that if block B is going to move up or just be at the verge of moving up ##Mg \sin \theta ## will act downwards and maximum static friction will act downwards ## \mu Mg \cos \theta ## Now what im confused by is how will we know " how quickly" block B reaches its maximum static friction value without any numbers, the suggested solution says that when block A is at its maximum extension, then block B will start to move up but with a certain set of values couldn't block A reach...
TL;DR Summary: Find Electric field due to charges between 2 parallel infinite planes using Gauss law at any point Here's the diagram. We have a uniform p (rho) density of charges between 2 infinite planes in the cartesian coordinates system. I used a cube of thickness a that spans from z=-a/2 to z=a/2 as a Gaussian surface, each side of the cube has area A. I know that the field depends only on z since there is translational invariance in x and y directions because the planes are...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Back
Top