Question regarding the output for AC circuit with capacitors

7 replies · 2K views · last reply
karan000
Messages
8
Reaction score
1

Homework Statement


Circuit schematic with an AC voltage source and series resistor feeding a capacitor, then an ideal diode in series, with a second ideal diode shunting to ground and an output capacitor across vo.

Both diodes are ideal.

Answers:
(a) Vi
(b) -Vi
(c) -2Vi
(d) none of the above


Homework Equations


Q=CV

The Attempt at a Solution


1. For t=0 to Pi:
Cap1 and Cap2 are in series and hence Q1=Q2, therefore Vc1 = Vc2.

From this we get Vi = Vc1 + Vc2, hence Vc1 =Vc2 = Vi/2.

2. For t=Pi to 2Pi,
Circuit schematic: AC source with series resistor feeding a capacitor (marked + and -) labelled v_i, followed by an output capacitor (marked + and -) labelled v_o, with a shunt node between them.


The circuit should look like 3 batteries in series as such:
Circuit schematic with a voltage source Vi on the left, a battery labelled Vi/2 on the top wire, and a second battery labelled Vi/2 in a vertical branch, with + and - terminal labels and a handwritten check mark and b.
,

Therefore Vo = -(Vi + Vi/2 + Vi/2) = -2Vi,
And so the answer is (c).

BUT...
Couldn't the circuit look like this too?

Hand-drawn circuit schematic with a source Vi on the left, a battery Vi/2 on the top wire, and a second battery Vi/2 in the middle branch, with red annotations V = 0.5 Vi at the top node, V = 1.5 Vi at the bottom node, and Vo marked across the output terminals on the right.


And so Vo = - (1.5Vi - 0.5Vi) = -Vi
Thus the answer is (b) ?

BUT...
We are just taking the voltage drop across the resistor, so Vo= Vc2 = 1/2Vi
So the answer is (d).Which is correct and what exactly am I misunderstanding?
 
Last edited:
karan000 said:
1. For t=0 to Pi:
Cap1 and Cap2 are in series and hence Q1=Q2, therefore Vc1 = Vc2.

Check that. What about the left hand diode?

(I assume you mean Vi is +ve during t=0 to Pi)
 
It's worth spending a moment just looking at the two diodes. What do the diodes mean for the polarity of the output voltage? Think.. What would need to happen to make it +ve? What would need to happen to make it go -ve.
 
I hope this is a step in the right direction,

1. For the first positive cycle, Vc1 = Vi and Vc2 does not charge is there is a short circuit due to the left ideal diode
2. For the first negative cycle, Vc2 = Vi + Vc1 = 2Vi. As the polarity of the output terminals reversed, the output should be -(2Vi).
3. For any positive cycle afterwards, the Vo remains -(2Vi) due to the short circuit from left diode.
4. For any negative cycle afterwards, Vo remains -(2Vi) as verified from 2.

Two hand-annotated voltage-doubler circuit diagrams: an AC source with series resistor, two capacitors, two ideal diodes and an output capacitor, with red and green marks showing current paths and the equations Vc2 = Vi + Vc1 = 2Vi and Vo = -(2Vi).
 
karan000 said:
2. For the first negative cycle, Vc2 = Vi + Vc1 = 2Vi. As the polarity of the output terminals reversed, the output should be -(2Vi).

Think about the right hand diode. How does a -ve cycle affect the output at all?
 
CWatters said:
Think about the right hand diode. How does a -ve cycle affect the output at all?

The diode is reverse biased, so no current flow. Hence Vc2 to remains uncharged also and Vo is 0 for both the positive and negative cycle?
 
  • Like
Likes   Reactions: CWatters
That's what I think. To get Vo = -Vi (or -2Vi) the output diode has to be the other way around like this..

Circuit schematic of a voltage inverter: a square wave source feeds capacitor C1 into a node with diode D1 to ground and diode D2 leading to the -V out terminal, with electrolytic capacitor C2 across the output and ground.
 
  • Like
Likes   Reactions: karan000
CWatters said:
That's what I think. To get Vo = -Vi (or -2Vi) the output diode has to be the other way around like this..

Circuit schematic of a negative voltage doubler: a square wave input feeds capacitor C1 and diode D1 to ground, then diode D2 and capacitor C2 produce a -V out terminal.
Many thanks for your help!