Jet Engine performance in Cold Weather

AI Thread Summary
Jet engine performance improves in cold weather due to increased air density, which allows for greater mass flow through the engine, leading to higher thrust. While thrust can be mathematically shown to be independent of ambient temperature, real-world factors like maximum RPM limitations of compressors and turbines play a crucial role. Cold air enables more mass flow at maximum RPM, allowing for increased fuel combustion and thrust. However, certain conditions, such as engine inlet restrictions at low speeds, can complicate this relationship. Overall, colder temperatures enhance jet engine performance primarily through increased mass flow rather than direct thrust dependency on temperature.
ZoraxDoom
Messages
2
Reaction score
2
Hey guys.

I was studying up jet-engines and their performances with varying ambient temperatures and found myself stuck on something that is probably very trivial.

What I've read online and in my notes is all generally the same - that as temperature falls air density rises and as such more mass is pushed through the engine leading to better performances at the same power.

While the material I've been given to study from agrees with this, it also states that the Speed of Airflow through the engine is proportional to the square root of temperature.

So if we take Thrust as: Mass * (Jet Air Velocity - Aircraft Velocity), we can get:
Thurst = Density of Air * Area of Entry for air at engine inlet * Velocity of Aircraft * (Jet Air Velocity - Aircraft Velocity)
These two mean the same thing.

Now, the step between here and the formula I show next has not been explained, but I believe it goes along these lines - given that mass flow increases as pressure does, but decreases as temperature does, we can say that Mass is proportional to (Pressure/Temperature)

Thus, Thrust can be taken as proportional to (Pressure/Temperature) * (Square root of Temperature) * (Square root of Temperature).

Thus, the temperature term cancels out, and we see that Thrust produced by the engine is actually independent of the Temperature of the ambient air.

So I don't understand this - if the Thrust produced by the Engine is independent of the Temperature of the ambient air, then how does it give better performance at lower temperatures?
 
Engineering news on Phys.org
I'm not sure exactly what situation you are talking about in your OP, but for "real" jet engines the thrust produced is limited by the maximum RPM of the compressors and turbines. The stress in the rotating parts increases with the RPM, and the RPM that causes the maximum permissible stress is (almost) independent of ambient temperature.

At the maximum RPM, cold air gives more mass flow, which let's you burn more fuel, and produces higher thrust.

Real life is not quite so simple of course. For example on some engine types on the Boeing 747, you can't actually reach the maximum permitted RPM in "cold" conditions at sea level when the aircraft speed is zero on the runway, because the engine inlets restrict and distort the airflow. You can only reach the maximum RPM and thrust as the aircraft speed increases during the takeoff roll. But that is not a big problem in practice, because you have much more thrust available taking off from sea level at Reykjavik in Iceland, compared with a hot day and a runway 9000 feet above sea level in Nairobi.
 
Zoraxdoom:

“Thus, Thrust can be taken as proportional to (Pressure/Temperature) * (Square root of Temperature) * (Square root of Temperature).”
Personally I think the conclusion is not very proper, because "Speed of Airflow through the engine is proportional to the square root of temperature." should has some premises and some limits, you might ignore the conditions.
for your advise
 
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'
Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly

Similar threads

Back
Top